LG DLE2514 Electric Dryer - Answered Questions & Fixed issues
Dryer won't turn off.
Is it a mechanical timer you turn (the "clickety-clank"-kind) to set the time? Sounds like something in it has been worn out. Shouldn't be too hart to get a replacement for it,t and you should also probably be able to replace it yourself unless you're very "un-handy", or want to play it safe.
9/19/2022 11:55:39 PM •
LG DLE2514...
•
Answered
on Sep 19, 2022
•
18,873 views
Where is the sensor
If you're talking about the moisture sensor, it's located in the lint filter casing. Remove your lint filter and look inside the casing. About 4 to 6 inches down on the right-hand drum side of the casing and running to the center, you should see two flat metal arcs following the contour of the casing. These metal arcs are the moisture sensors
8/29/2014 1:36:22 AM •
LG DLE2514...
•
Answered
on Aug 29, 2014
•
301 views
Dryer says check filter and it is clean
Air flow in the duct work is restricted... and the dryer sensor thinks that the filter is clogged.
You will need to take a fluffy cleaning wand and, with the filter removed, try loosening up some of the accumulated line in the duct.
Next, remove the lint pipe from the wall connector and try cleaning it and the pipe for as much distance as you can reach.
Finally, go outside and check the vent. It needs to be clean and clear of obstructions... also, needs to close when the machine is off.
You can do testing on the outside vent with "air dry" setting - hot air is not required... Keep cleaning ductwork until the outside vent passes air freely.
After air flow is restored, the sensor in the "VENT" alarm will act nice.....and stay off
11/6/2014 5:10:34 PM •
LG DLE2514...
•
Answered
on Nov 06, 2014
•
923 views
Lg dryer wont start lights on on but wont start
Check the thermal fuse, start switch on the control panel and door switch because all three are more likely the cause of the dryer not starting up.
The door switch is often the culprit in this type of fault, although a faulty drive motor is not ruled out.
7/5/2014 8:36:40 AM •
LG DLE2514...
•
Answered
on Jul 05, 2014
•
844 views
How to turn off the child lock on a dryer
This information is from the manual:
Child Lock can be used to prevent your children from changing options on control panel while the dryer is running. When child lock is enabled, all the buttons will be locked and Child Lock glows. To enable Child Lock, Press and Hold OPTION for 3 seconds, A single beep tone is heard and Child Lock is displayed on the status window. To disable child Lock, press and hold OPTION for 3 seconds again.
5/30/2014 1:03:47 AM •
LG DLE2514...
•
Answered
on May 30, 2014
•
2,184 views
Inside dryer silver flaking off
If you need a new drum. Follow the instructions below.
Ordered drum from Sears parts. 3045EL1002D
Cost of 85$ + 15 to ship. It came in 5 days.
Here is how to do it on a DLE2514W. Takes about an hour. I only used a phillips screw
driver. Take your time and look over the situation. I hope that I rememberd
everything. Good luck.
Dryer Drum Repair
Dryer Drum Repair
1. Remove L bracket with 6 screws at the top, rear.
2. Slide top back 2 inches to unlatch and remove.
3. Remove control panel with 2 screws at top, inside corners.
4. Carefully unplug 4 plugs from back of control panel.
5. Looking at inside at the top. Remove wiring bundle from 2 guides.
6. Unplug wire from dryer light.
7. Open dryer door and unscrew 2 screws behind door just below lint trap.
8. Remove 4 screws at top of front panel that holds the door.
9. Lift up front panel to remove. I couldn't get the door switch plug to disconnect
so I carefully rotated it an set it on top of the dryer.
10. Remove upper case bracket with 2 screws in front and 2 screws inside at top.
11. slide up a bit to unlock from sides. Watch routing of dryer switch wire bundle.
12. Remove lint trap duct with 2 machine screws. Carefully slide down to remove.
13. Remove front drum support with 4 screws attached to sides. Lift up to disengage
sides. Lift drum to free from rollers.
14. Observe how drive belt is routed around motor and tension roller. Push tension
roller up and release belt. Carefully take belt off and remove.
15. Almost done. Lift drum up at rear to free from rear rollers. Remove.
16. While your're there vacuume up dust and reverse procedure to install.
4/13/2014 1:02:29 AM •
LG DLE2514...
•
Answered
on Apr 13, 2014
•
240 views
Dyer won't shut off
Cool - no pun intended. The timer mechanism is not working properly.
11/23/2013 11:06:31 PM •
LG DLE2514...
•
Answered
on Nov 23, 2013
•
56 views
19:F1. UO1
This error code tell you the safety thermostat is not working. This part is on the top of element cover. Replace new one.
10/17/2013 5:44:30 AM •
LG DLE2514...
•
Answered
on Oct 17, 2013
•
306 views
How would I test the humidity sensor in my
If the sensor was replaced but not help, the issue may be from control board. You do not say why you did replace a sensor, this part is hardly to be faulty.
10/17/2013 4:59:44 AM •
LG DLE2514...
•
Answered
on Oct 17, 2013
•
96 views
Not finding what you are looking for?