20 Most Recent
Husqvarna 23 Hp 48" Deck Yard Tractor - Page 5 Questions & Answers
On a husqvarna gth2448 engine dies when letting up
Do you mean the engine dies when you place a load on it? As in letting out the clutch/brake so the engine has to work by moving the mower, or in engaging the blade clutch so the engine has to spin the blades?
If so these V-2 engines have a propensity towards bent valve push rods, as did my 2148, which can knock one cylinder out but still run so long as little or no load is on the engine.
If not a power issue, then I would look to an electrical problem. I think you have to depress the pedal to start, must be a switch there somewhere activated by the pedal position which could be bad.
What replacement battery
any lawn battery will work most part stores has them just take your old one with you to machem up
Have to run tractor on full choke
Sir if you are running it on full choke then there is a blockage in the high speed jet inside the carb. Best solution would be a carb cleaning Hope this helps good luck!
TRANSMISSION LOOSES PULLING POWER AFTER WARNING UP
Unfortunately, but I'm not 100% sure on your model, it is a sealed transmission. I have had the same problem on an lgt2654 husqvarna and the service center just ordered a new transmission to replace the faulty one. Fortunately it is warranted for two years and I'm covered. Curiously though the service center suggested that this unit, even though advertised as a garden tractor with all kinds of pictures of attachements, is not meant for moderate to heavy usage. i.e. pulling a lawn sweeper or yard cart full of dirt. I most definetely will re think my next purchase! Good Luck
Brake acts like it's not releasing fully...holding
the brake caliper is rusted closed causing the pads to stay enguaged, dissasemble the brake caliper and remove the 2 pins and de-rust them with emory cloth. reinstall them with anti-seze and reasemble the brake caliper back onto the transmission should be good to go!
I need a mikuni fuel pump for the fh 531 v kawa
Use the Briggs & Stratton Fuel pump instead. The Briggs part number is 808656. It's more easily available, and the same or lower in price than the Kawasaki part number 49040-7001. Roughly $30.00.
Mikuni makes them both and they are identical.
Hope this helps.
Brake will not release on my Husqvarna riding mower
the brake caliper is rusted closed causing the pads to stay enguaged, dissasemble the brake caliper and remove the 2 pins and de-rust them with emory cloth. reinstall them with anti-seze and reasemble the brake caliper back onto the transmission should be good to go!
Transmission fluid low, hydrostatic transmission
Quoted from your Owners Manual. . . . .
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department.
The mower starts, the blades will engage, but when
Here is a dumb question for you, are you sitting on the machine when you release the petal?
Most new machines have a 'operator presence' safety system on them. To run the machine, the operator must be in the operators regular position. I would guess you know this.
Can you release the brake and continue to run with the mower off???
Maybe your machine requires you to engage the drive and then the mower???
So, if the engine dies when you engage the drive system, the tractor thinks there is no one in the seat. Look for a switch malfunction under your seat.
Please let me what happens. Id like to solve this for you.
a
Need to replace front left tire. Can't get it
If you have removed the hub cap (dust cover), the E-clip or cotter pin and washer from the outside of the wheel, it should just slide off the shaft but you may have a burr of some sort stopping it, try some sanding cloth, about 220 grit and smooth out the circumference of the shaft. If this still does not work, try pumping the wheel full of grease if it has a grease zerk on it. If the wheel turns freely when off the ground, you have something not clean or perfectly round stopping the outer race of the bearing
Blade wont start
Check the linkage on your hydro drive.Follow shift lever from handle to trans axle and see if linkage is ok. :)
Husqvarna YTH20K46
Is this the first time cutting grass with a lawn tractor?
How tall of grass?
Use the grass cutting heigth adjustments on the tractor to a higher setting when cutting tall grass. Cut again to a lower height setting on the second pass. Grass higher than your tractor is not good for your tractor. Follow the manual instructions for best results.
Not finding what you are looking for?