Frigidaire FDL50R1 Dehumidifier - Answered Questions & Fixed issues

Read the instruction manual thoroughly and ensure you did everything exactly. If it still doesn't work it is faulty and should be returned.

Hi,
There can be many reasons why a dehumidifier will not work or collect water.

Here is a tip that I wrote to help people to figure out what is going wrong with their dehumidifier

Dehumidifier is running but no water is in bucket
http://www.fixya.com/support/r4662409-dehumidifier_running_but_no_water_in

heatman101

Good Afternoon Friend, that's a great question! Typically the FILTER RESET light will illuminate after 250 hours of operation. To locate the filter, remove the bucket and the pull filter downwards. The filter can be clean by using clean water or vacuum cleaner extension hose. If you use clean water, please allow the filter to dry. Once you reinstalled the filter then replace the bucket. To extinguish the light simply press the FILTER button and your dehumidifier should resume normal operations. Remember it is best to clean your filter every two weeks based on normal operating conditions. Hope this helps! - Z

Hello friend, that's a great question!

The best way to clean your Frigidaire dehumidifier's coil is by using a brush attachment from your vacuum. I hope this is helpful. -Matt

Hey friend, thank you for the post!

I understand that your dehumidifier continuously is set at 50-60 and the clean filter light has not stopped. I would like to ask you some additional questions in order to provide you better assistance. First, does the appliance still collect water? Secondly, have you tried to reset the appliance? I look forward to your comment back so that I can further help you. -Matt

Hello Friend, this is Z. I am happy to assist you! If you are receiving an error code AS on your Frigidaire dehumidifier, it typically means that your dehumidifier is experiencing a sensor failure. Because it is a smaller appliance, repairs are often more costly than the actual appliance replacement. Is your appliance still in warranty? If so, you might want to reach out directly to the manufacturer to determine the coverage on your dehumidifier and the procedures to any potential remedy in that regard. Best of luck!

Good Afternoon Friend, I understand that you want to know how to measure the humidity in a room with your Frigidaire dehumidifier, model# FDL50R1. Typically, your appliance will not measure the humidity and tell you exactly what the level is. I suggest placing your dehumidifier in the room you want it in, and turning it on to the continuous mode. The display will show "CO". Leave it at this setting for the first 3-4 days. Once the 3-4 days has passed, I suggest setting it to the 50%, 60%, or 70% setting and change it to your liking. If it is more humid in the room than you would like, put the setting lower. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful. -Best Regards- WP

will not come on screen is blinking stop

Hi Kim - I understand that you removed the styrofoam inside the dehumidifier float thinking it was packing material, however I would recommend contacting the manufacturer to verify if it the part is available and can be replaced.

CO means Constant On

Is there a actual hole in the tank where your hose connects? Is there a piece of dirt clogging the hole in the tank.

Water runs down hill ... if there is a hole in the tank for the water to get out and the hose is clear and it is going down hill ... it must drain. The entire length of the hose has to be flat or down hill and no kinks.

Let me know what you find please

a

Hello there,
Your guess is right as to what the cause of the problem is. The relative humidity (RH) sensor is faulty and need to be replaced. That is why it is stuck on 30%. When the RH is faulty, the compressor will not run. And the dehumidifier will not do anything.
Hope the moisture collected in the bucket is removed, becuse that also could be a cause of the problem. If the bucket that collects moisture is full, the sensor will send a message to the compressor and have it shut down automatically till the bucket is empty.
Once it is confirmed that the moisture collecting bucket is empty and it is still not reading anything other than 30%, then that confirms the problem to be from the RH sensor.
Hope this helped. All the best. Elect_Comp

No, you didn;t miss anything. The drain tubing inside the hose connection on the back of the unit may be clogged. To solve this problem, turn the unit OFF & unplug it. Then disconnect the hose from the hose connection.

Using an appropriately sized, 18" long, plastic Zip Tie, carefully insert the tip of Zip Tie into the hose connection & tubing. Continue to push it in until you reach a bend in the tubing. You will need to gingerly work the Zip Tie past this bend, until it either bottoms out or you run out of usable Zip Tie. Then slowly pull the Zip Tie back out while rotating (twisting) it. This will breakup any clogs. As you reach the inserted end of the Zip Tie, be prepared, as some water may follow.Reconnect the hose to the unit , plug the unit in and turn the Master ON/OFF Switch to ON. Set the humidity extraction level to 35% or Maximum if you have a manually controlled unit. Allow the unit to run, while you monitor the hose end for water flow. It may take 10 to 15 minutes for the water to start flowing, so be patient. Also, be sure the hose you're using is no longer than 48". Drainage relies entirely on gravity.

NOTE: If you don't have a Zip Tie, you may use something similar ( i.e.a long pipe cleaner), but NO wire coat hangers.

Hope this helped you to solve the problem. Thanks for choosing FixYa.

Hi,Here is a tip that I wrote that will help you understand why and what you cando with a dehumidifier that ices up.Dehumidifier is Freezing up and not workingheatman101

Hi,
There are many reasons why a dehumidifier willnot work or collect water.
Here is a tip that I wrote to help people to figure out what is going wrongwith their dehumidifier

Dehumidifier is running but no water is in bucket

heatman101

The dehumidifier has a non-removable tray under the coils (they look like radiators) that collects and drains the water away. If the tray or drain gets clogged with dirt or slime the water doesn't drain away well. Some water is picked up by the fan and is blown out the vent. Take the covers off the machine and give everything a good cleaning. If you get water on any electrical parts, let the machine dry thoroughly before plugging in.

theres a plastic knock out plug in the bucket that needs to be popped out then it will drain through the hose

The faulty float valve is almost always the problem, based on what you described. It is a replaceable part, but you may have to but the entire bucket assembly. Generally, they run around $50.00. However, not all parts are still available for that model, even though it's only 4 years old.

If you want pursue finding the float valve or a new bucket assembly, the best place I've found is online is Appliance Factory Parts http://www.appliancefactoryparts.com/search/index.php they carry parts for just about any appliance you can think of.

Or Frigidaire Parts Select
http://www.partselect.com/Entry.aspx?Source=GAWS&Brand=Frigidaire&Term=frigidaire&gclid=CIfU4u28vqkCFcPd4Aod6CC5hQ

I hope this helped you. Please let me know. Thanks.

Hi,

Here is a tip that I wrote that will help you understand why and what you cando with a dehumidifier that ices up.

Dehumidifier is Freezing up and not working

heatman101

Dont spend to much time trying to repair dehumidifier they are very cheap to replace. Most dehumidifiers have lots of problems because they are made so cheap. Just replace the dehumidifier you will tank me in the end.