20 Most Recent
Panasonic Viera TH-42PZ80U Plasma TV - Page 3 Questions & Answers
Why is Power indicator light blinking
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
Won't switch on but light flashes red
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.
How to by panasonic panal th 42pv7hs
Yes it should still be covered find ur direction book and check out ur warranty and see if Panasonic will come out and cover it. Always beef up ur story you have been Panasonic owners for years when u call them. You have gotten all of ur friends and family to switch ect... Even if it's not covered sometimes loyalty goes a long way.
Remote control will not turn on tv or digital box
assuming that you have changed the batteries, I say, like ours, it was dropped many times. if that is the case then the sensor light is finished, kaput, busted. your best bet is to buy a universal remote and program all your devices in it. " one remote, no headaches".
Panasonic viera th-p42g10a plasma tv has
The number of flashes is indicating a specific error. If you let me know how many times the light is blinking I will let you know whats most likliy causeing the issue. Reply to this same post for assistance.
How do I download a quick guide start up manual?Pan
All cable company's have a remote that can also control your TV. Flip your cable remote over and find the part number on it. On rare occasions, it might be inside the battery department instead of the back. Type that part number into your internet browser with the words guide or manual and you should find the manual u need to program your TV into your cable remote. If all else fails, call your cable provider.
I have s Panasonic flatscreen tv and I've been having a problem with it, when ever my power goes out or I unplug my tv it won't cut back on for atleast a week, what's wrong with it and what can I do t
Since this question is almost a year old, I don't know if you have fixed the problem or thrown the TV in the rubbish bin, but looks like you're still waiting for a response. If so, here is my answer. It could be that these TV's have a back-up battery that discharges if left unplugged for some time and might reactivate the system once fully charged. It could be an environmental factor too. Maybe room temperature is too high that makes the TV shut down to avoid damaging the components. Is the TV near a fireplace or heater? There are Panasonic customer support centres, you should email them and ask, but, I would recommend you make a clear and concise explanation what exactly do you mean by the words you wrote here. Sure, I understand that when you unplug the TV, and then you plug it back on and it does not cut, cut? What do you mean by cut? Are you trying to say it doesn't work and that the pilot light doesn't come on until a week later? You don't even explain how long you had the TV unplugged. did you unplug and then plugged it right away, or did you unplug it and then plugged it a few months later? whatever it is, I suspect this TV must have a back-up capacitor as a battery. Or it could be that some damage has been done during an electrical storm, but I doubt it. Best ting you can do is leave it connected and observe if it repeats the same problem. If it does after a short disconnect then reconnect of the plug, it may require an expert check-up by an authorized TV repairmen, because this is really an unusual occurrence. Hope your problem will be sorted, or has it? It's almost a year now.
My plasma TV makes vibration sound when volume increases on TV or any remote of DVD, STBs
It is an issue of automatic gain control software for the audio signal. The issue happens if you have a short outage of your cable signal. The TV tries to amplify the audio signal that isn't even there. When the signal returns, the TV software is not programmed correctly to drop the amplification (not automatic gain decrease -just increase). The only solution is a factory reset of the TV.
Here's how...
https://m.youtube.com/watch?v=s0CJpgbDEgw
Ours is a 50inch . It just turned it self off and
Film capacitor Is bad. So the power relay and capacitor need to be replaced. One pretty much wears out the other. Parts are a pain to get a hold of. But very cheap. 1/2 dozen of each cost around 50 cents delivered from overseas.
Relay is a small rectangular box. It's what makes the clicking sound. Film capacitor is usually yellow or blue colored. Rectangular with two leads to the board. Almost directly next to relay.
Pushed the power button but
Hi.Please check the fuse of your television located inside the TV.Try to remove the back cover of your TV and find the fuse location.Its located at the back right near the power supply.Check it if is busted and replace the same valiue of fuse.Unplug the TV before removing the cover to avoid electric shock.tanks
How do i get ride of subtitles on a panasonic?
I am not familiar with "ride", it would have to be something that is programed in from the remote. If you still have a manual for the remote it would be your best bet. Some of those remotes and all the functions are a nightmare. If you do not have you can probably go to the Mfg. web site and enter the model # and down load a manual for it. Good Luck.
Col. Dana Gillespie
Not finding what you are looking for?