NEC NP200 Projector - Answered Questions & Fixed issues

1,white spots appeared on screen,means the DMD is broken,you need a new DMD. Have a good day! We supply original projector parts: lamp, bulb, Lcd, Lens, DMD, motherboard, powersupply ... with high quality and competitive price. Jerry China Tel: +86 131788 67858 E-mail: [email protected] Skype: lampdeng.com YM: [email protected] http://facebook.com/lampdeng http://www.lampdeng.com

I have 2 NP-200 projectors installed in a school which show white dots on a black background and black dots on a white background. This is caused by the DMD chip losing pixels. Only solution is to replace the chip, I'm researching now if that i an economical solution.

Dusting is not going to help. I could be the lamp if it happens with no input hooked up.

I have several white dots all over the screen. They're more that pops up as I watch it and the dots never goes away. Does anybody know what I need to do to fix this problem? Thanks..

I have about 10 of these in the school I work in, most of them have gone mental flickering, my solutions has been to open the covers remove the bulb and carefully using a compressor blow all the dust out..This has worked and cured them in about 6 out of 8 cases

sounds like an electronic problem rather than an optical fix.
Has she changed the setup of the unit recently

Phone NEC and get them to swap it over if it is under warranty. They are very good like that and you will have a replacement next day via TNT. Take out the bulb and keep hold of all the cables and remote as they will send you the projector only. Put the faulty one in the box and send it back. TNT will collect it and it is part of the returns policy. No cost involved.

hi, it depends how you connect the DVD to the projector. the projector itself has only one speaker (mono) - not so good for movies. the "audio in" is a mini stereo plug (same as headphones). you will need a RCA to mini stereo convertor - red/white (or red/black) RCA to mini stereo plug.
or you can connect a RCA to RCA (red/white to red/white) cable to an amplifier which is connected to speakers.
or just plain speakers, but you'll probably need a convertor cable from RCA (red/white) to a female mini stereo plug).
these cables are pretty cheap and can be bought in any Radio-shack.
hope it helps....

What input are you using and what is your input source?

Thanks for your question!
I'm sorry that you haven't received an answer yet.
The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...
Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.
Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

All here and also the Service Manual in Scribd.

C4101 error code Bizhub 350

Copytechnet https://www.copytechnet.com > ... > Konica Minolta Apr 23, 2010 - C4101 code at power up. Description: C4101 code at power up. Solution: PROBABLE CAUSES: 1. Failed PWB-A (Mechanical CB). Missing: NEC ‎IT3640D

IT40D Series Service Manual ' PDF

Scribd https://www.scribd.com > doc They are sharp and may hurt you. Be sure not to leave the packing material inside the system. It may cause a system malfunction or a fire.

SOLVED: Error code c4101 - Konica Minolta

Fixya https://www.fixya.com > ... > Bizhub 362 Copier Oct 25, 2012 - THE COPIER DISPLAYS ERROR C4101. C -4101 Polygon motor error. Change the polygon motor ,if you can not reset the malfunction code.

Based on the information provided, it is possible that there may be an issue with the projector's power button or internal components. It is recommended to try the following troubleshooting steps: 1. Check the power source: Ensure that the projector is properly plugged into a working power outlet and that the outlet itself is functioning correctly. 2. Reset the projector: Some projectors have a reset button or option in the settings menu. Try resetting the projector to see if this resolves the issue. 3. Check for internal issues: If the above steps do not work, there may be an issue with the projector's internal components. It is recommended to contact a professional technician or the manufacturer for further assistance. In summary, if a NEC projector indicates light when plugged into a power source but does not turn on when the power button is pressed, it may be due to issues with the power source, internal components, or other factors. Troubleshooting steps such as checking the power source and resetting the projector may help resolve the issue, but professional assistance may be required if these steps do not work.

1. To turn on your NEC P350x projector, press the power button on the top of the projector. 2. To reset the timer on your NEC P350x projector, press the Menu button on the remote control. Then navigate to the "Timer Settings" menu and select the "Reset" option.

If they are not physically broken, brake cleaner and cotton wool will get them clean. Don't put them back in the wrong way around!

Don't know if this will work as I don't run anything from Microsoft. I sue a proper OS; Linux. https://driversol.com/drivers/printers/microsoft/nec-superscript-860

M300w use LCX102 LCD panels Sony Lcd panel is not durable the font strokes are weak, The color of the black font is not black enough It means the lcd panel is failed there are 3 lcd panels in the projector Red Green Blue 3 lcd panels are failed you need a new whole prism block with 3 lcd panels

I suspect the ballast (supply for the HID lamp) has failed due to an expired lamp. Probably not ecconomic to repair.

Incorrect replacement lamp I would think.

Six flashes is lamp error. Either the lamp and/or balast unit has failed.

Your statement indicates'there is a fan issue'. It may just require cleaning but may need replacing. Nothing to do with the lamp, unless it has overheated and also needs replacing.