Sharp MX-2300N Color Copier - Answered Questions & Fixed issues

It means that your fuser unit has reached its lifespan: you can still use the machine but be aware you will need a fuser rebuild in the near future

Ok so the DK code means that the Black drum counter has reached its limit
To clear this you need to clear this easy you want
# , * , c , *
To enter service mode
Type in code 24 press start
Then you want sub code 07
Then you can select what you want to clear so the bk drum unit
Execute this yes then press the CA key the machine will restart and away you go
I also do advise that you service representative comes along at some point to check the machine it could need parts because if you stretch the life of parts your machine could become unreliable... But that is up to you.

Try reinstalling print driver, or upload a PCL5e driver.

https://www.manualslib.com/manual/490400/Sharp-Mx-2300g.html Review and follow directions.

probl?me: code error sharp AR-452 U --- H5-01

Worn cleaning blade or fuser roller.

E7-20 is problem with laser unit - Black. Check connectors, optical axis of laser beam (in case there were assembly / disassembly actions). Laser unit can be defective.

Hi Doni . Have you got a black toner cartridge to swap with the one in the machine ?

yes you can clean it with methilated spirits or any alcohol

In order to scan you need your smtp server adress and dns server address.You also need a valid e-mail address.In command prompt type ipconfig /all and find the details there

Hi, This error is due to a small grey arm, approximately 2 inches long, that has been removed from the delivery assembly of the machine. This is a common occurrence where by the operator reaches in to remove copied or printed documents & accidently dislodges the arm. If you look at the rear of the centre tray you may find the detached arm. The arm clips into a small black hinged projection located in the centre of the delivery assembly in the upper part of the machine within the centre tray area. You will need a torch or other light source to see into the delivery unit. The unit itself slides back & forth as part of the delivery assembly & is the mechanism that provides the offset feature of sorting. If the arm cannot be located then, unfortunately, you would require a dealer to provide a replacement arm. Hope this helps.

The code refers to the black drum reaching the end of its life. Sometimes you will also have a VK code that is displayed along with the DK code. This refers to the black developer life. Both drum & developer have a life of 100,000 copies which is why you tend to get both codes at the same time. The maintenance code should still allow the copier to photocopy & scan as normal, so if the copy quality is still OK then the machine should continue as usual & the codes are reset when the drum & developer are replaced. If you have a problem printing to the copier from a PC when the maintenance codes are displayed then this can be rectified 2 ways. The 1st way is to have the parts replaced & the counters reset. The 2nd way is to turn off SNMP setting within the printer driver. If you open printers & devices & locate your printer. Right click on the printer & scroll down to printer properties half way down the list (not the properties at the bottom of the list). The third tab along the top should be Ports. Click this tab & this will show the port details of your printer. Click on configure port & this will open another box. At the bottom of the box to the left there is a tick box with SMNP enable. If the box has a tick in it, untick the box, click apply then close all the open windows. This allows the printer to print when the machine displays maintenance codes. Hope this helps. Dave.

could be anything maybe a strap holding the machine damaged a connector or plug on a board came loose, have a tech come out and look at it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

How do you know its the blade, does this happen when you print? or when you copy?? if copy is happening when going thur the document feeder ?? if so place the original on the big glass then make copy if it goes away the its on the small slit glass to the left or right of the big glass Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

check the paper trays ensure guides are set correctly and check behind the draws no paper stuck behind, also remove any paper from draws which is considered storage paper. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try this site http://siica.sharpusa.com/product-downloads Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Try this #, Interrupt,c,interrupt use the ten key pad type 16 press start ok start interrupt ca Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Check the transfer and seperation assy directly under the drum Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Trouble content When separating the primary transfer belt unit, change in the separation position sensor characteristics is not detected within the specified time. Section PCU Case 1 Cause Harness connection trouble between the PCU PWB and the separation position sensor Check and remedy Check the harness between the PCU PWB and the separation position sensor. Case 2 Cause The belt position sensor is not interrupted or it is always interrupted. Belt separation clutch operation trouble Check and remedy Use SIM6-3 to check the belt separation operation. Case 3 Cause The primary transfer belt unit is not installed. Check and remedy Install the primary transfer belt. Hope this help you, good luck!!!

check the current in simulation for all color or clear the charge grid for all the colors