Top 20 Patton Electric HRH316 Ceramic Mid-Size Heater Questions & Answers

I just used an old toothbrush and stuck in in between the grate holes on the front. I Just brushed on and around the sensor really well & it seems to be working fine now.

There is a round sensor under the heating elements which sets off the alarm when it thinks it is overheating on the PRH11. Unfortunately, a dirty sensor will fool it into reacting like it is overheated. I cleaned the sensor which was dark and revealed it to be a lighter goldish maybe brass in its original color. If your sensor is dark, it will continue to trip the alarm for overheating and will need to be replaced. If you were lucky like I was and can clean it, the problem should be resolved and it will operate like normal until it gets dirty again. This procedure lasted for 3 days and I had to clean it again. I believe I left the dirt on too long and now my sensor has tarnished plus I live in a rural area with significant dust requiring this recleaning every few days. I only used a damp paper towel with water to clean. Cleaning may work better with alcohol or a tarnish removal solution.

It's rating upto 4 out of 5 stars

Yes, there is/was a recall on some Patton Heaters, but I don't recall if your model # is one of them. For more info search Google for Patton Heater Recall Notice and you'll find the correct site.

not too good! they didn't start the "ener-guide" program until around 1996.

Twin ceramic heaters are intense, but, not intended for indoor use without adequate ventilation.They radiate heat and patton is a reputable brand in heating devices.

Parts suppliers in the link. Ot if you take the old one off, a metal fabrication workshop could make you a new one. https://www.google.com/search?q=Newlec+NLSH+24AN+storage+heater+parts They still sell them and they all look the same. https://www.hwelectric.co.uk/newlec.php ..

To fix code E5 on a Bonaire evaporative cooler, which typically indicates a water management issue, try the following steps:

1. Check the water level in the unit to ensure it's sufficient.
2. Inspect the water inlet valve for blockages or malfunction and clean or replace as necessary.
3. Clean the filter and pump to ensure proper water flow.
4. Reset the unit by turning it off at the power source, waiting a minute, and turning it back on.

If the problem persists, consult the user manual or contact Bonaire customer support for further assistance.

Obviously window and wall a/c units are not tradable, in spite of the fact that I don't have the subtleties of the distinction. Alter Window units are intended to exploit the way that a window is a flimsy segment; vents outwardly of the a/c case can be near within part of the a/c unit, yet be outside (where they must be). This might permit the window units to be less expensive. Interestingly, a wall can be 6" thick or more; wall units should have all vents near the rear of the unit. BTW I generally felt that the vents in the side of a window unit were for admission of air at encompassing temperature to then be coordinated through the condenser curl at the back plane of the unit to be depleted out the back (presently more sweltering than surrounding), however as a matter of fact a portion of the side vent region may likewise be utilized for ousting air which cools engines. It may be the case that in a window unit the venting on one side is committed to admission of air for the condenser loop and the venting on the opposite side is for exhaust. This would forestall the hot exhaust air being pulled in the admission for the condenser cooling air. Window ACs versus Through-the-Wall ACs It's not difficult to think about window and through wall ACs, since they're comparative in cooling limit and size, yet through-the-wall units will generally be somewhat more productive in light of the fact that they make an impermeable seal in the room. The significant contrasts between these ACs include establishment and venting. Window ACs fit through a window and don't need long-lasting establishment, while through wall ACs are really incorporated into the wall - making them well known in rooms without windows or for individuals who like to let their windows be. Wall forced air systems normally just vent warm air through the rear of the unit, while window ACs vent from the sides and back. Hence, window and through wall models are not exchangeable (regardless of whether they're a similar size). Generally speaking, in the event that a window unit vents out its side, the wall will obstruct the vents and cause overheating. Select window AC models can be introduced through a wall, however provided that they have a slide-out case wall sleeve. Peruse more on wall sleeves.

bad compressor

Impossible to answer without 'make model (what is is)'. That should be the first 3 words in every question.

Troubleshooting ' Air Conditioning and Refrigeration

Daikin https://www.daikin.com > products > ac > services > trou... If the operation lamp still flashes, disconnect the power plug from the outlet or turn the breaker off and contact the place of purchase. Are there any objects ...

Air Conditioner Light Blinking Problem Solving Techniques ...

absolutesolutions.com.sg https://www.absolutesolutions.com.sg > news > why-my... Nonetheless, a blinking light is mostly an indicator that your unit needs to be serviced if you expect it to not only service you back but to do so efficiently.

Have model ras-17ekv-ul green operation light and orange

JustAnswer https://www.justanswer.com > HVAC Questions Jun 25, 2020 - You may have had a power failure. Try resetting the breaker. Flashing green indicates power loss. Flashing orange for outdoor circuit board ... 1 answer · Top answer: It shouldn't as long as the unit is off when you kill power. ..

Question edited for clarity. Bad luck, and the company will get some negative advertising by your question as this will end up indexed by Google. There are some vendors for spare parts. If it is just a multicore wire that was damaged, that is available by the foot. https://www.google.com/search?q=human+touch+ZERO+GRAVITY+G+2+remote+replacement ..

The compressor has overloaded. I would power it off and leave to cool for 30 minutes the power on again to start it up. If it has still got the error, call a maintainance engineer.

Question edited for clarity. Stuck blend door actuators, stuck thermostat, or this, airlocks. https://www.fixya.com/support/r29872074-vehicle_cooling_system_no_heat ..

Greetings from Mississauga, Ontario! If it is construction Styrofoam it is a good insulator. Fill as best you can between the studwork and use spray foam to fill gaps. Then cover with drywall. Floor insulation and underfloor heating is a good way to keep the chill out. Frozen pipes and only caused by cold and draughts. Stay warm. ..

It is not the fan motor. it is most likely the computer board. can you take a picture of the unit and send it to me? text it to 3153418739

Blocked jets clogged with dust or dirt, blocked injector need a clean / service

o reset your Homebasix Oscillating Parabolic Heater, follow these steps: Unplug the heater from the power source. Locate the Manual Reset Button on the heater. It's usually a small button or switch. Use a fireproof, non-conductive rod (such as a wooden stick or plastic tool) to press the Manual Reset Button. After resetting, plug the heater back in and check if it functions properly. Remember to ensure that there are no flammable objects within 3 feet of the heater and that it is placed on a stable surface.

Check the breaker. They have a 5 year warranty.

Warranty - Franke HT-400 Installation Manual [Page 12]

ManualsLib https://www.manualslib.com > ... > Installation manual use, for a period of ?ve (5) years from the date of purchase. This warranty will be honored provided the HT-400. Heating Tank has been installed and ...

From the owner's manual:

• Open front thermostat door and open battery compartment door.
• Install two new "AA" alkaline batteries. Locate the positive (+) ends of the batteries and match them with the positive (+) terminals located in the battery compartment. Close battery compartment.

Going by the photo of the thermostat, it looks like there's a finger recess or latch on the right side of the thermostat that you pull on to swing the front open. If there is unexpected behavior from the thermostat after replacing the battery, see the reset procedure in the installation section of the manual. Link to manual: https://thermostat.guide/proselect/proselect-pstsl21p52-2h-1c-programmable-thermostat-installation-guide/#battery-replacement