3Com NBX 3101 - Answered Questions & Fixed issues
Nbx auto answer
Hi,At Two scenarios it will be happening.1. When your phones act as a intercom.2. When your server settings are enabled with auto-answer option.Check with server admin.-Karthik.
10/20/2012 2:17:45 PM •
3Com NBX 3101
•
Answered
on Oct 20, 2012
•
182 views
Change the time on the clock
This must be done on the phone system as the administrator. For 6.0 software go to System-wide settings, set date and time, and you can set it there. For 5.0 and older, go to Tab to it, System configuration, system settings, date and time. Once the time has been set on the phone system the date is updated instantly on the phones (even before your browser finished loading the next page).
7/27/2010 11:12:05 PM •
3Com NBX 3101
•
Answered
on Jul 27, 2010
•
1,661 views
Call Forwarding --Help
The phone may be apart of a hunt group. Inside of the Net Set Utility, check to see if it is a member of that hunt group.
3/3/2009 10:27:42 PM •
3Com NBX 3101
•
Answered
on Mar 03, 2009
•
180 views
Voicemail in use message
Reboot the phone system (through the browser) and this should take care of it. There are limited voicemail ports and sometimes they get put on hold and can't be released. I have seen it a lot. some versions of software can clear this but a reboot will take care of it.
11/11/2013 11:49:24 PM •
3Com NBX...
•
Answered
on Nov 11, 2013
•
73 views
I have AVI Video and it only plays sound
Ok it is may be do you to system is old needs up to date , so that the video may not have downloaded completely from the source web portal. The media player present in your handset is outdated.
HI,
I have two 3com
I don't know anything about these units, nor do I have time to source any docs for you, but maybe you can try connecting a PC directly to the port your patch panel is connecting the the switch from, you can at least see if that port is working.
My next and only other suggestion is to invest in a "LAN cable tester". In my area, you can find cheap ones for U$20.
The tester will allow you to check connectivity between any two ports, and allows you to test both patch links and individual CAT5/6 cables.
Good luck!
Facebook recovery
notify the police dept / person handling the case and let them know about the face book information
I want to know how I can re-set my 3Com 3crwe955275 wireless access point to its default factory settings. Can anyone help?
1 Remove power from the Gateway.
2 Disconnect all your computers and the cable/DSL modem from the Gateway router.
3 Using a straight through Ethernet cable, connect the Ethernet Cable/DSL port on the rear of the Gateway to any one of the LAN ports.
4 Re-apply power to the Gateway. The Alert LED will flash as the Gateway starts up, and after approximately 30 seconds will start to flash more slowly (typically 2 seconds on, 2 seconds off). Once the Alert LED has started to flash slowly, remove power from the Gateway.
5 Remove the cable connecting the Cable/DSL port to the LAN port, and reconnect one of your computers to one of the Gateway LAN ports.
6 Re-apply power to the Gateway, and when the start-up sequence has completed, browse to:
http://192.168.1.1
and run the configuration wizard. You may need to restart your computer before you attempt this.
7 When the configuration wizard has completed, you may reconnect your network as it was before
Here on page 85 of the manual
3Com 3CRWE53172 User Manual Forgotten Password And Reset To Factory...
What is 3x phone
For 3Com that would mean a 3100 series or 3500 series phones. The 3100 series phones are for NBX and VCX phone systems and the 3500 series phones are for VCX only. Both are also SIP compliant.
Db9 rj45 pinout
Here is the standard pinout for a console port on a router to seriel port for computers
How reset 3com 4228g switch
If I remember correctly, there is a tiny hole at the back or on the side. Press a paper clip into it. The switch should do a full reset and then reboot. If its just locked up, I would switch off at the power for 15 mins and try let it do an auto restart itself. Do this before you go doing a full button press reset as you may lose any or all updates the switch has had loaded into it.
Network card driver
Are you able to remove the card from your PC?
and read the model on it?
Are you able to find your motherboard/computer model?
use the motherboard/computer model to find what model of card is on it.
Once you have the nic model search for a driver.
3COM 3100 entry phone, how to configure SIP
From Digium Mailing List:
3Com 3100 series phones do not support SIP with non-3Com systems. They have a basic boot loader which must download code from a 3Com NBX or a 3Com VCX system. If you don't have either of these, then you won't get runtime code on the phone, thereby making it impossible to use the thing with Asterisk.
Asterisk Users 3Com Phones
Not finding what you are looking for?