Top 20
Whirlpool DU1055XTS Built-in Dishwasher Questions & Answers
When dishwasher drains the water
It's most likely that the filters in your dishwasher are blocked, the best way to clean them is to remove the filters from the bottom of the dishwasher, place them in the racks and run through the hottest wash cycle. It also helps to have a dishwasher cleaner inside the machine at the same time, these are available from most places that sell the dishwasher powder.
5/15/2017 3:36:03 AM •
Whirlpool...
•
154 views • 0 helpful votes
I have a brand new whirlpool DU1055XTV5
Have installer come back to you, sounds like a pump problem, blockage, timer, ...is outlet hose kinked at all? It usually goes into the kitchen sink drain below.
4/4/2017 12:12:03 PM •
Whirlpool...
•
163 views • 0 helpful votes
How to replace front metal panel
Usually (in most Whirlpool models), if you open the door and look, you will see 8 to 10 screws around the perimiter of the door. Remove those, and the outer door panel will come loose from the inner panel. Now just lift the door up a little bit (an inch) to remove it from the 2 catches at the bottom, and you should be able to remove the outer door panel. If you need further help, reach me via phone at
https://www.6ya.com/expert/ronald_e6b9572cebe3ad27
5/15/2015 7:18:10 PM •
Whirlpool...
•
144 views • 0 helpful votes
Whirlpoo l
Probably because the locked up setting needs to be removed or changed. I have never owned a dishwasher. My advice is to remove the dishwasher and sell it. Then soak your dirty cutlery and crockery in hot soapy water in your sink for about twenty minutes, then wash them yourself. Don't be lazy. You have to load and unload a dishwasher anyway.
8/19/2014 2:42:33 PM •
Whirlpool...
•
72 views • 0 helpful votes
Whirlpool dishwasher wdf310plab4 will not drain
If the pump can be heard running, check for blockages (filter and hose), What sort of head (siphon height) is involved ? (ie. is water running back). Do you have a "check valve".
If no no pump then ....
a) check you are at the start or end of a cycle.
b) the pump may be seized or defective.
c) machine thinks it is drained.
It is most likely the pump unit, but you will need to investigate that yourself. Download a parts book. The pump is about $50.
I gather it is out of warranty. So this is my best guess.
5/7/2014 11:41:02 PM •
Whirlpool...
•
119 views • 0 helpful votes
Need reset sequence for dishwasher
see this causes, use the common sense.God bless youDishwasher Stuck in a Cycle
If your Dishwasher is stuck in a cycle check the following
Float Switch
The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the
tutorial and the
video for checking this part.
Timer / Control
If your dishwasher gets stuck in a cycle first try shutting off the
breaker for at least 5 minutes if this does not correct the problem you
will need to
replace the timer / electronic control.
9/19/2012 2:39:26 PM •
Whirlpool...
•
814 views • 0 helpful votes
Dishwasher not getting hot
Is your sink getting hot water? If no then probably your hot water heater needs adjusted or heating element in it replaced.
9/20/2012 3:47:08 PM •
Whirlpool...
•
137 views • 0 helpful votes
I have a model #DU1055XTSQ2 It has no lights on, it will come on for about 30 seconds to go off and will come on again for several mintues. Do you think it could also be the thermal fuse?
Hello.Everyone expects their dishwasher will work correctly.
They can become nonchalant about it until one day it does not function.
Sometimes the dishwasher doesn't drain as expected. Most people
immediately call the plumber when their dishwasher doesn't work. There
are several things you can try at home before having to pay an
expensive service fee.
1 Check the basics. Make sure that the dishwasher has actually
finish the cycle. Your dishwasher will not drain until the end of the
cycle. Many things may have interrupted the cycle. Check circuit
breaker and reset it if appropriate. Also check the fuse. It is
possible that you could have tripped a circuit have way through the
cycle. Make sure the door is properly closed. Ensure you have chosen a
cycle on the dishwasher. It is amazing the problems children could
accidentally cause, that are easy fixes.
2 Remove any excess food at the bottom of the dishwasher. The best way
to do this is with your hands. Large food particles can block from
going into the drain.This is also another extremely easy fix to make
your dishwasher to drain.
3 Check to ensure that the hoses are still attached. Use your manual to
find where the hoses are. If they are not attached the owner's manual
will give you instructions on how the attach the hoses to your specific
dishwasher.
4 Attempt to declog the line. Disconnect the hose from under your sink
and check to see if there are any clogs. Use a hanger or towels, remove
the clog from the hose.5
Remove the dishwasher basket. Again refer to your owner's manual for
specific instructions.Normally you will remove it with a screwdriver.
Make sure to work slowly. As you take the basket apart, you will be
able to see if it needs to be cleaned. If there is dirt or debris, you
can clean the parts with a rag or paper towel. After cleaning these
parts, you can replace the basket.
Thanks.
12/17/2011 11:08:45 PM •
Whirlpool...
•
164 views • 0 helpful votes
DU1055XTSQ3 only HI-TEMP WASH, SANI RINSE, HEATED
Hi
First make sure that nothing is blocking the drain pump
assembly that is located inside the lower front panel of the dishwasher. If the issue
returns after its cleaned then it means that the control board has gone bad and
should be replaced. Hope this helps...please post back for further assistance.
Daniel
7/30/2011 1:09:26 PM •
Whirlpool...
•
290 views • 0 helpful votes
My dishwasher will not start.
Hi
First make sure that nothing is blocking the drain pump
assembly located inside the lower front panel of the dishwasher. If the issue
returns after its cleaned then it means that the control board has gone bad and
should be replaced. Hope this helps...please post back for further assistance.
Daniel
6/16/2011 6:50:36 PM •
Whirlpool...
•
89 views • 0 helpful votes
The dihwasher will not start and the clean light
If this is a Whirlpool manufactured dishwasher (such as the one pictured), the blinking clean light is an interruption in the dishwasher program that usually indicates a component problem or program malfunction. If a component is defective, it is commonly attributed to the heating cycle or thermostat related problem. To rule out component failure, or program error, the following link explains how you may be able to clear the blinking clean light problem and possibly avoid a service call:
http://www.fixya.com/support/r3575752-dishwasher_blinking_clean_light
Keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.
NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.
In many cases, I found this to be a momentary glitch in operation. If the problem keeps reoccurring the number of flashes is an indication of WHICH circuit is causing your problem. As all dishwashers differ in operation and features, refer to your tech sheet for the recommended troubleshooting steps.
NOTE: Some dishwashers use the Sani-Rinse/Air Dry combination, some use the Sani-Rinse/Heated Dry combination. Some use a sequence of three, others use a sequence of 5 pushes of the buttons. If the tech sheet is not located behind the lower toe panel, it should be affixed somewhere under the dishwasher. I have also found them located inside the inner door panel.
If you still need assistance, please post back and let me know
5/9/2011 1:09:41 PM •
Whirlpool...
•
175 views • 0 helpful votes
Water will not drain after completion
Check the bottom of the dishwasher (where the water drains to) and check there's nothing blocking it? Maybe give the filter a rinse to clear it.
4/24/2011 5:18:10 PM •
Whirlpool...
•
91 views • 0 helpful votes
Cloudy dishes not cleaned tried every option
Hi,
I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher
SprayArms not Spinning
How to Buy
ApplianceParts OnlineA bad heating element causes many problems in dishwashers...
Dishwasher Problems The
HeatingElement not WorkingDishwasherMaintenance
DishwasherResidue and Film on Dishes
heatman101
Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes
;
';
';
4/28/2011 3:07:58 PM •
Whirlpool...
•
59 views • 0 helpful votes
Not finding what you are looking for?