20 Most Recent FoodSaver Smartseal V3485 Brushed Stainless Steel and Black - Page 4 Questions & Answers

The belt is part of the pump that delivers the cleaning solution according to an unverified source.. You might query Hoover. . https://www.amazon.com/Hoover-440005353-Original-Equipment-Manufacturer/dp/B00F9A4FJI Also works with FH50252 Hoover Power Scrub Elite Pet. https://www.youtube.com/watch?v=yEbRVwRhsPg How to Replace a Hoover Shampooer Hose Pump Spin Scrub - YouTube which I am informed applies to your Hoover as well. Sorry I cannot provide a more direct answer. Try Hoover customer service.

There is probably a blockage in the pipe or on the entry to the motor. I would take it to pieces and clean it.

https://www.hunker.com/12498375/why-does-my-vacuum-smell-like-burnt-rubber https://www.doityourself.com/stry/if-your-vacuum-smells-burnt-check-these-6-things Good luck.

Here is the manual.

http://www.manualnguide.com/dl/20341/

Good Luck and please Rate Fixya!

1. Sweep, dust or dry mop daily.
2. Vacuum weekly.
3. Clean heavy-traffic areas with a damp mop twice a month.
4. Clean with recommended hardwood floor cleaner once a month.
5. Apply a fresh coat of finish every three to five years

1. Check the drain system: Make sure that the drain valve or plug is fully closed and not leaking. If there is any water present, drain it completely before proceeding.
2. Reset the unit: Turn off the unit and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This can sometimes reset any error messages and resolve the issue.
3. Check the water detection sensor: The unit may have a sensor that detects the presence of water in the tank. Look for the sensor and make sure it is clean and free of any obstructions. If there is any dirt or debris on the sensor, clean it gently with a soft cloth.
4. Contact customer support: If none of the above steps work, it's best to reach out to the manufacturer's customer support for further assistance. They can provide specific troubleshooting steps for your particular unit and guide you through the process of resolving the issue.

Remember to refer to the user manual that came with your unit for specific instructions and recommendations.

If the cap on your Living Solutions steam vac won't stay down, it could be due to a couple of reasons:

1. Incorrect positioning: Make sure the cap is properly aligned and seated on the unit. Check if there are any obstructions or debris preventing it from fitting securely. Clean the cap and the sealing surface if necessary.
2. Damaged or worn-out seal: The cap may not stay down if the seal inside is damaged or worn out. Inspect the seal for any signs of cracks, tears, or deterioration. If it's damaged, you may need to replace it. Contact the manufacturer or refer to the user manual for guidance on obtaining a replacement seal.
3. Defective cap or pressure release mechanism: It's possible that the cap or the pressure release mechanism itself is defective. If you've ruled out other causes and the issue persists, you might need to contact the manufacturer's customer support for further assistance. They may be able to provide troubleshooting steps or offer a replacement part if needed.

Remember to always follow the manufacturer's instructions and safety guidelines when working with steam cleaning devices.

Impossible to guess what you have Google make model height adjustment repair All questions need 'make model (what it is)' as first 3 words please. https://www.google.com/search?q=%E2%80%8Bmake+model+height+adjustment+repair ..

fixya doesnt sell products or stock them ---do an online search for replacement

Question edited for clarity. Help and Support in the link https://www.google.com/search?q=Rug+Doctor+PSC-1+reassemble+handle

first no info generic answer and fixya doesnt sell products --for parts etc try manufacturer--or online search

Wheres the thermostat located

The slip ring contacts at the canister end of the Miele SES 125-3 hose are responsible for transmitting electrical power to the motorized brush head. Over time, the slip ring contacts can become dirty or corroded, which can cause the brush head to stop working properly. Here are the steps you can follow to restore the slip ring contacts: Unplug the hose from the vacuum cleaner and remove the brush head. Look for the slip ring contacts inside the canister end of the hose. You may need to use a flashlight to get a good view. Use a small brush or a cotton swab to gently clean the slip ring contacts. Be careful not to apply too much pressure, as this can damage the contacts. If the slip ring contacts are heavily corroded, you may need to use a mild abrasive to remove the corrosion. Be sure to use a non-abrasive cleaner specifically designed for electrical contacts. Once the contacts are clean, use a dry cloth to remove any excess cleaner or debris. Reattach the brush head and plug the hose back into the vacuum cleaner If the slip ring contacts are damaged beyond repair, you may need to replace the hose or take it to a professional for repair.

Question edited for clarity. Blinking White Light = The robot is upgrading or resetting. It it never stops, contact their Support https://trifo.com/pages/support ..

A completely white screen with white vertical lines on your Mitsubishi WD 77731 TV can be an indication of several possible issues. Here are some potential causes:

1. Faulty T-Con board: The T-Con board is responsible for processing the image signal and distributing it to the screen. If the T-Con board is faulty, it can cause the white screen and vertical lines issue.
2. Loose or damaged cable connections: Loose or damaged cable connections can interfere with the transmission of the image signal, causing the white screen and vertical lines issue.
3. Failed backlight: The backlight of the TV illuminates the screen from behind. If the backlight has failed, it can cause the screen to appear white.
4. Damaged LCD panel: The LCD panel is the display screen of the TV. If the panel is damaged, it can cause the white screen and vertical lines issue.

To troubleshoot the issue, you can try the following steps:

1. Check the cable connections: Make sure that all cables connecting the TV to the source device (such as a cable box or gaming console) are properly connected and undamaged.
2. Power cycle the TV: Turn off the TV and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on.
3. Check the T-Con board: If the T-Con board is faulty, it may need to be replaced. You can check for any visible signs of damage or contact a professional to diagnose and replace the board if needed.
4. Check the backlight: If the backlight has failed, it may need to be replaced. You can shine a flashlight on the screen to see if there is any image visible, which would indicate a failed backlight.
5. Contact a professional: If none of the above steps resolves the issue, you may need to contact a professional for further diagnosis and repair.