Hi wvchic1979,
We looked up that model and we found it corresponded to a Harbor Breeze Otter Creek ceiling fan. Is this your fan?
We found the following page which has more details on how to obtain a manual for this fan,
https://harbor-breeze-ceilingfans.com/harbor-breeze-otter-creek-ceiling-fan/
Let us know if this helped.
Cheers
if the machine will not start properly.
my guess would be check door swtich: Also did you check for burned out breaker at power box? check for full voltage to the maching from the wall outlett. then check
Push start switch may need to be tested with a multi meter for continuity OHMS should show a closed circuit when pushed in or turned on. The start switch on some is often part of the timer and is activated by pulling out on the timer knob. Although not normally available as a separate part, the switch can be tested for continuity with a multi-meter. You will need to remove power from the appliance and then locate the correct timer contacts as noted on the wiring diagram. On some electronic controlled models, the start switch is a momentary contact type switch located on the control console. You can test this switch for continuity with a multi-meter when the push button is held inDoor switch if bad can be jumpered with a bypass, fisrt check with meter for ohms. Or open line cirrcuit this switch can hinder operationIt may have a bad centrifigal motor switch that my have been tripped. check belt tensioner Electric dryer no start does nothing
Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage.
CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING.
NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position.
If you hear a humming/clicking sound from motor area you more than likely have a bad motor.
Try this test out to see if u have weak windings or relay/capacitor on motor.
Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings
Another thing to check is the belt safety switch. With a multi meter.
Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released.
Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad.https://www.youtube.com/watch?v=MhVUEhngZMg
https://www.youtube.com/watch?v=9xD7lCXJ0ZM
https://www.youtube.com/watch?v=sTRP6kHqAFsHey GOD IS GOOD !!!! WHICH IS WHY MY ADVICE IS FREE
I found the articles on Harbor Breeze helpful for solving remote control problems. You can also check out the video below as well.
I found the articles on Harbor Breeze Accessories helpful for solving remote control problems. You can also check out the video below as well.
IT IS THE STARTER CAPACITOR NOT CHARGINGING UP TO INITIALLY CRANK MOTOR TO RUN SPEED,, BE VERY CAREFUL AS MOTOR WILL GET EXTREMELY HOT AND COULD MELT WIRING AS AMPERAGE NOT GETTING RELEASED, JUST LIKE HOLDING AN ARC WELDER TO LONG WHEN ROD STICKS
Based on the information provided, it is possible that the issue lies with the Zing Ear ZE-208D 3 speed switch. This switch controls the fan speed and if it is not functioning properly, it could cause the fan to only run at the lowest speed. It is also possible that there could be an issue with the transformer or another component, but without further testing it is difficult to determine the exact cause of the problem.
One potential solution would be to replace the Zing Ear ZE-208D 3 speed switch. This can be done by disconnecting the wires from the old switch and connecting them to the new switch in the same configuration. It is important to ensure that the new switch is compatible with the fan and has the same number of wires as the old switch.
Another potential solution would be to check the wiring connections between the switch and the fan motor. Loose or damaged connections could cause issues with the fan speed.
If neither of these solutions work, it may be necessary to consult a professional electrician or contact Concord for further assistance.
The flashing lights on your Bush TD7CNBCW tumble dryer could indicate an error or fault in the machine. While I don't have access to specific error codes for this particular model, I can provide some general troubleshooting steps that may help you identify and resolve the issue:
1. Check the user manual: Refer to the user manual that came with your tumble dryer. It should contain information about error codes and their meanings. Look for any reference to the flashing lights you are seeing.
2. Power cycle the dryer: Turn off the dryer and unplug it from the power source. Wait for a few minutes, then plug it back in and try turning it on again. Sometimes, power cycling can help reset the machine and clear minor glitches.
3. Check the door switch: Ensure that the door of the tumble dryer is fully closed and latched. The machine may not start if the door switch is not engaged properly.
4. Clear any obstructions: Make sure the drum inside the dryer can spin freely and is not obstructed by any items or lint buildup. Clear out any debris or lint that may be blocking the drum or the lint filter.
5. Check the water tank and filter: If your tumble dryer has a water tank or condenser unit, ensure that it is empty and clean. Additionally, clean the lint filter to ensure it is not clogged, as this can affect the dryer's performance.
6. Consult customer support: If the issue persists and you cannot find a resolution in the user manual, it is recommended to contact the Bush customer support or a qualified technician who can provide specific guidance and assistance for your model.
Remember, safety should always be a priority when dealing with electrical appliances. If you're unsure or uncomfortable with troubleshooting the issue yourself, it's best to seek professional help to avoid any risks or further damage to the appliance.
-undefined-undefined-4.jpg)
