Sony Playstation 3 (40 GB) Console - Page 8 - Answered Questions & Fixed issues
How to resett Sony av system arm-adp022
Hold down ?/1 for 5 seconds.
After "CLEARING" appears on the
display panel for a while, "CLEARED"
appears.
All the settings you have changed or
adjusted are reset to the default settings.
What is the wpa key for 2wire014 for my
2wire014 is a wireless router. If it is yours, the wpa key should be on a label on the bottom of it. If it isn't yours, then it is a neighbors or someone close by and you probably cant get it.
How to get gold on skyrim
Best way to get gold on Skyrim is to build up your alchemy skill. It takes a little time, but if you find the right ingredients, you can make potions worth upwards of 4000 gold. One recipe I can think of off the top of my head is, Giant Toe, Wheat. Makes a potion worth about 2000 gold. There are many many more.
How to delete psn account
Hey, try getting a new memory card, because all the memory cards for the ps vita have their psn accounts locked on permanently to it! So my solution is to get a bigger and new memory card! Preferably the 32 GB ones.
Ps3 code 80028E02
Unplug your router for about five minutes and turn off your PS3 and unplugg it for about five minutes as well. Sometimes its a cache problem.
If this does not work try setting up your DNS address manually on your PS3 under Network settings.
Change your primary DNS code to 129.250.35.250 and your secondary one to 129.250.35.251
Hope this helps!
visit the
CBR Tech Solutions
How to solder a loose wire from a psp go sony charger
First you will need a pin out of the adapter.
Tools you will need are.
1: Solder with rosin core thin solder would be best
2: Soldering iron lower watts the better
3: Flux to clean the surface you want to solder to
4: Sponge to clean the tip of solder iron
If you don't have any of thous supply's it would be cheaper to buy a new cord. Also if you don't have vary much experience soldering i would also recommend getting a new cord for the fact you can cause more damage than good.
To get the solder iron ready you need to heat it up. Once it is hot enough to melt the solder apply the solder to the tip and let is set there until you want to solder. You have to clean the tip off with a wet sponge but not soaked in water just enough to get it wet. Every time you go to solder Clean the tip off and apply fresh solder to it not a lot just enough to cover the tip when you want to solder. When you go to store the iron apply a small blob of solder to the tip to keep it from oxidizing.
Strip the wire shielding off a bit longer than the size of the contact you want to solder. Twist the wire and put flux on the surface you want to solder and tin them.
Tinning the wire is just applying a small amount of solder to the wire as to hold the strands together and make it easier to transfer the heat and solder to the contacts. Now mach the pin-out to the weirs to the contacts and put flux on the contact you want to solder to. Clean the surface by applying flux to it.The surface will be oxidized and will not let you transfer heat or solder to the surface. The key to soldering is to use the right amount of heat , solder and time you hold the iron to what your soldering to. You want to make sure you touch the wire and the contact you are soldering to as to transfer the heat to both items at the same time to make the solder flow. Put the solder wire to the tip of iron that is touching the wire and contact and not on top of the iron tip. Any time you apply heat to solder joints you want to use flux to keep them clean and free of oxidized material. After you solder check the solder joints for cracks, uneven and dull surface. You want the solder to look as shiny as possible and smooth. If it looks like it has waves or holes and cracks it means you have a cold solder joint and must reheat and apply flux with a small amount of solder to fix it .Here is a link to help you out this is not my site and full credit goes to the owner of site.
How To Solder Soldering Tutorial Also put a link to a new cord if you decide you want to get a new one. Here is a link that may or may not help with the pin-out. Also not mine it should credit the poster on the forum as he did all the work i just found it
PSP Go Cradle mini USB Tutorial with Partial Pinout PSP Go Acidmods com
How do I do a hard reset to my sony PlayStation 3 system
Hard Reset procedure for the PS3 (as instructed by Sony CS).
Be sure to backup your settings/games saves by doing a System > Backup on your PS3 or you may lose your game saves! Also, this is a last resort procedure prior to exchanging/returning to sony.
1. Power Off the PS3 via the power switch in back and power back on w/switch.
2. Hold Power Button on the Front until you hear 3 beeps.
3. Then go through the initial setup and then run a full Format via System > Format. (will take approx 3 1/1 hours). You may need to have our AV cables ready if your using HDMI (in case HDMI isn’t detected after initial reset).
4. Restore your backup you made prior to doing factory/hard reset (optional, if you created a backup).
Not finding what you are looking for?