20 Most Recent Parrot 3200 Ls Color Handsfree Bluetooth Car Kit - Page 8 Questions & Answers

Hi there,

Well Please follow the below steps -

1 - Remove any access panels you need to access the radio.

2 - Remove the radio & disconnect the wires from it.

3 - Hook up one side of the ISO harness to the car and the radio. It only fits one way.

4 - Hook up the other side of the ISO harness to the Parrot harness. It only fits one way.

5 - Connect the Parrot harness to the Parrot blue box.

6 - Connect the Parrot display ( if your model has one ) to the Parrot blue box.

7 - Install the battery in the Parrot remote.

8 - Turn on the ignition. At the Parrot title screen, simultaneously press Green, Play/Pause, and Red on the Parrot remote to pair it to the blue box. You should be able to press the knob on the remote and control the system. Your phone will still need to be paired, but wait until later to do this.

9 - If everything works, turn off the ignition. You should see the "goodbye" message. If not, check the wiring and try again. You must connect the ground wire on the Parrot harness to a good ground or it will not work at all!

10 - Disconnect your car battery to prevent the A pillar air bags from deploying in case you hit something you shouldn't while running wires.

11 - Remove the A pillar cover on the drivers side, run the mic wire, replace the cover.

12 - Run the USB, iPod, Line In wires to the glove box or wherever you want.

13 - Connect the car battery.

14 - Turn on the ignition and confirm that the system is still working.

15 - Follow the directions in the manual for pairing your phone to the Parrot.

15 - Turn off the ignition and re-install the radio and any other panels you removed.

Please post comments for more help or information............

Good Luck!!

Thanks

reset factory settings of ur mobile if it don't works then get flashed ur fone.

Hello,

I had the same issue with my Nokia phone a long time ago. To solve that issue I had to upgrade the Parrot's firmware with the laptop through bluetooth connection while in the car. I have done this a few times to get the most out of my parrot.

I recently got a Blackberry and had no issues with the contacts whatsoever. I do have to say that I dont have 500 contacts, but only 130.

If I were you I would try to update the Parrots firmware to the latest one available in the parrots website.

I am not sure if the parrots has a maximum contacts restriction. That might be also your problem.

Hope it helped.

1234 but you might need to delete a few devices if you have problems, go to settings in the parrot and then to paired devices select phone then push the middle button in, select delete and then push the green button

Enable the bluetooth mode on your phone, next on the hands free kit, scroll through the menu untill you come to "Settings Pair with phone" A four digit pin number will appear on the screen, remember it, once the search is finished, "Parrot 3200" will appear on your phone screen, make the selection and then enter the pin number and confirm it. The message "pairing sucessful" wil appear on the 3200 LS color. To see this information, scroll to page 8 after you click on the link. Click on the link to download the owners manual:

http://www.parrot.com/documents/parrot_ck3200_userguide_zone_c.pdf

2 ways of doing this. Go in to the bluetooth menu of your phone and search for the device, it will come up parrot 3200ls select this and it will give you a pin on the screen enter pin in the phone when asked and hay presto! you will have to send over the contacts tho, you do this by going into contacts then options, mark, mark all, send, via bluetooth, select the parrot, and it will send them all over. The other way is if it doesnt give you a code on the screen when pairing, go in to settings, pair with phone, then other phone, pin will come up. search from phone and then select.

problem is the 220 has an amplefier in boot the controls the radio, unless proper leads that connect there are used to interupt the radio when call happens it just some thing u have to put up with or buy the lead, try autoleads.com or look on parrot web site for the right leads

A well known auction site has brackets for these but I normally stick them flat to the dashboard.

Dan

yes you can do this by going into settings then scroll all the way down to the bottom and select factory settings the push the middle button in. then push the green button for yes.

http://www.parrot.com/es/apoyoalcliente/guasenlneadelaayuda/parrot3200ls-color

Trate este lazo, busque su teléfono en la sección de compatable y dará instrucciones.

Ta Dan.

Try this from Parrot.com, cheers Dan

Performing object push process:
** On the Carkit go to Settings / Contacts Management / Receive Contacts

* For one contact sending:
* On the phone go to MENU / CONTACTS
* Select a contact to send by pressing OPTIONS / SEND BUSINESS CARD / VIA BLUETOOTH
* Select the 3200LS from the list, that will start the file transfer process

* To send all contacts:
* On the phone go to MENU / CONTACTS
* Select OPTIONS / MARK/UNMARK / MARK ALL / OPTIONS / SEND BUSINESS CARD / VIA BLUETOOTH
* Select the 3200LS from the list, that will start the file transfer process

you may need to update the parrot software and also make sure you phone software is upto date. you can try sending contacts manually by going to contacts / mark all / send as business card / via bluetooth.

i could give you more buy you have not mentioned your phone make / model.

try parrot .com for more.

Go to settings/ pair with phone/ other phones. it will then give you the code to use, then search for new paired device from your phone, when it finds parrot, click pair and enter code shown on parrot screen. Make sure you delete all other paired devices from parrot first. instructions can be found at parrot.com

BlueTooth devices only can support so many profiles of different phones etc. From the main menu, go to Settings, then Paired Devices, List then delete.

Try all com ports, eventually one should work, try deleting all paired devices from your parrot, it may be full.

Send my an e-mail, I can explain you the solution for the error "memory full" [email protected]

I updated the software. That solved all the problems

umm on what? your phone, your puter....sounds like a mute function