20 Most Recent A.O. Smith Pump Motor, 1/2 HP, 3450, 115/230 V, 48Y, ODP - USQ1052 - Page 2 Questions & Answers


No, you cannot.

Plumbing | Answered on Oct 18, 2019


That pump doesn't have a pressure switch! It has a digital flow sensor on discharge. It will keep running so long as there is a flow. Usually caused by dripping tap, or leak. Pressure doesn't stop the pump. By the way - Don't expect to get parts from Canadian Tire or Mastercraft - They told me that they carry NO parts for that pump. It is very similar to a Burcam pump and they may have parts or offer service.

Plumbing | Answered on Oct 17, 2019


https://www.boilerguide.co.uk/manufacturers/ideal/error-codes/ideal-f1-fault-code-explained

Plumbing | Answered on Oct 13, 2019


The most likely component failure is the battery. It should last several years when properly maintained and desulphated.

When properly installed the pump only runs when theres a failure with the primary pump. So it should last indefinitely.

Plumbing | Answered on Oct 08, 2019


Check this out on u tube

Plumbing | Answered on Oct 03, 2019


To modify the pressure:

· Start the pump.

· If the SET LED blinks, hold key + down until the SET LED

remains on.
· Then press keys + or - to modify the pressure value

Plumbing | Answered on Sep 27, 2019


check underneath to tighten it

Plumbing | Answered on Sep 26, 2019


There are lot of tools used by professionals for plumbing. I don't find any reason to buy all of them.

So, at first decide which tools you need or for which specific tasks. If you can figure out which tools you really need then check your local tools shop or you can buy tools from online also.

Buying tools didn't solve your plumbing problem, you have to have required skill to use those tools and knowing basic plumbing.

Thanks.

Plumbing | Answered on Sep 25, 2019


TAKE IT OFF A FLUSH FROM THE BACK END

Plumbing | Answered on Sep 24, 2019


TRY TURNING ON THE WATER A LITTLE THAT USUALLY POPS THEM UP

Plumbing | Answered on Sep 23, 2019


Take is apart and clean it, lubricate the parts. Replace plunger, washers and o-rings.

https://www.youtube.com/watch?v=qYiF3y5f9yI

Plumbing | Answered on Sep 16, 2019


Ebrud730:
There is a hex-nut configuration at back of the handle of your sprayer where the hose enters the back of the sprayer handle. You can use a wrench to unthread the back cap and hose and remove them. You will have full access to all of the goodies inside of the sprayer handle at that point. pull the parts out and clean them with a rag that has some tooth to it (such as terry-cloth) and wipe off the WD-40 and liquid wrench (they will adversely affect your "O-rings") clean off the o rings and plunger and re-assemble the sprayer. You may have to go to Home Depot or Lowes to get replacement "O-rings" to stop the leakage.

Plumbing | Answered on Sep 15, 2019

Not finding what you are looking for?
A.O. Smith Pump Motor, 1/2 HP, 3450, 115/230 V, 48Y, ODP - USQ1052 Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top A.O. Smith Plumbing Experts

Andrew Bugbee

Level 2 Expert

267 Answers

Tom Chichester

Level 3 Expert

54965 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you an A.O. Smith Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

A.O. Smith Plumbing

  • A.O. Smith Plumbing

Most Popular Question

wiring

  • Plumbing
Loading...