20 Most Recent LeapFrog FLY Fusion Pentop Computer Questions & Answers

Try leaving it hooked up to the computer for a while then after maybe a few hours try to turn it on again.

just leave it hooked to the comp for a while. than le it hooked an turn it on. wait till the compu loads

I posted the link for documentation responding rather than answer a dozen other posts with related requests.

I'm fine with giving answers for people, but do I have to pay FixYa after 30 days for the privilege of doing so?

Best, Mark

If you use it but don't use all the money it will take the remainder off.

what kind of phone do you have??? alot i have found are on Ebay! try that hope it helps

it just has to charge. whn i turns d its charging. leave it for 15min andn take it out and turn it on. if it doesnt tn on contact an expertfrom the place u got it.

no the on in the link is a fly pen 1.0 the one where you have a usb on the top is the fly pen 2.0

I just had this same problem, and the Fly Fusion website has this to offer (the website link is http://fly.custhelp.com/cgi-bin/fly.cfg/php/enduser/std_adp.php?p_faqid=1619&p_created=1201901554&p_sid=fj7lBboj&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPSZwX3NvcnRfYnk9JnBfZ3JpZHNvcnQ9JnBfcm93X2NudD04NSw4NSZwX3Byb2RzPSZwX2NhdHM9JnBfcHY9JnBfY3Y9JnBfc2VhcmNoX3R5cGU9YW5zd2Vycy5zZWFyY2hfbmwmcF9wYWdlPTE*&p_li=&p_topview=1 or you can go to Fly Fusion supprot link and click on the FAQ section to access this information):

Question Unable to install FLY World on Vista Answer If you are unable to install FLY World on the Vista operating system, please follow these instructions.

1. In windows explorer navigate to c:\windows\system32

2. Find the application named "cmd". Now right click on "cmd" and select "Run as Administrator"

3. In the following window, type or copy and paste

regsvr32 /u vbscript.dll

Now press enter. You may receive a pop-up regarding DllUnregisterServer that it succeeded or failed. In either case, click OK.

4. Next type or copy and paste

regsvr32 /u jscript.dll

Now press enter. You may receive the same pop-ups regarding the DllUnregisterServer message. Click OK once more.

5. We will next need to type or copy and paste

regsvr32 vbscript.dll

and press enter. You may once again receive the pop-up window. Simply click OK to continue.

6. Finally, type or copy and paste

regsvr32 jscript.dll

and press enter. You may once again receive the pop-up window. Simply click OK to continue.

7. Try running the installer again.

If you go to the LeapFrog Website and at the bottom select customer support you can then select the fly fusion.  The guide you are looking for is entitled "Fly Fusion Parent Guide" I know it's not named the way it should as it is a general guide and not just about account administration.
http://www.leapfrog.com/etc/medialib/leapfrog/fly/ffls_37735.Par.40053.File.dat//Users/na/Desktop/Parent%20Guides/FFLS_37735_PG.pdf

OK ... after a lot of trial and error, I got mine to work. I think it may be a really low charge or something. I had to press the power button until it was completely dark ... no flashing faint green or any colors. Then when I plugged it in, I got a solid red and left it for awhile. Then when I pressed the power button I got yellow, red and green ... the computer recognized it and then got a solid yellow.

Before when I had it plugged in, I'd get a lot of red random flashing ... and it just didn't seem to charge at all ... even after a full day.

I think the issue was that it was in this "flashing state (red when connected, very faint green when disconnected)" It wasn't easy to get it to turn off completely. Most of the presses of the power button didn't change the state at all. But if I got it just right, I could see the faint green light go off. That's when I plugged it in and got a solid red light, and eventually a good charge.

Hope this works for some others.

Try pressing the on/off button to turn it off. I had a same problem. I depressed the on/off button for ~6 second or so and the device turned off. When I turned on again, the LeapReader no longer had a white light and was recognized by my computer.

Enter 1111 and it will say oops wrong password then enter 419 backspace and get rid of the 9 and then 27 worked like a charm took forever to find one that worked and this one worked for me once in change the 4 digit code to something ez

That's what I've been asking.??

Get a new Leapster

uefwiagyrskef

https://s7.leapfrog.com/is/content/LeapFrog/Site%20English%20Assets/Support/Download/Parents%20Guides/80-602000-LeapPad-Ultimate-Parent-Guide.pdf