Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne - Page 3 - Answered Questions & Fixed issues

Take out the brush roller. (turn the plastic lock mechanism with a coin or screwdriver, pull out the plastic holder, and the brush will pop out). The brush roller has two white caps on the ends. Chances are, one or both of these caps have moved out just a bit, putting too much force on the delicate motor. Simply push the caps back firmly into place. Make sure the brush and the surrounding area is clean, put back in and It should spin .

dealextrem

if you are certain no blockages ? and the dust collector is clear/clean ? have you checked that the outlet filter which is located inside dust compartment is clean/clear this is usually a gauze filter its purpose is - as vac works and draws dust into collector the air that is sucked up thro vac builds up in collector chamber or bag on most vacs? and so for vac to maintain suction the air has to be able to escape to atmosphere/room without dust which is left insude chamber/bag if fitted and so air escapes via the gauze vent as prev mentioned ? however if gauze filter is not clear to vent then vacuuum is restricted due to air drawn being unable to expel sometimes on vacs they will eventually cut off due to o/heat but will operate when cooled so may i suggest checking the above possibility ?

The reason its stopping is because the belt is stretched out and when it rests on carpet or floor the weight of the vacuum presses down on floor causing more stretching and straining on belt. When belt heats from friction it gets softer thus causing more slippage.

So what's your question?

check online for the recall of those machines.

Hi there SmartAlec from NelsonVacuums.com.au here. I assume you are not from Australia as that machine is called an ergo rapido here. That machine here suffers from very dodgy switches but little else goes wrong. I would suggest it is a repair for a professional to replace the switch. If it is under 2 years old it should be a warranty repair. Hope this helps.
Happy Vacuuming! :)

Sounds like it. How long have you had the vacuum? That's one of the draw backs of wireless vacuums. On top of providing less than adequate suction, the batteries have poor life spans. I suggest you go back to where you purchased it from and see if they can help you with a new battery

www.totalvac.com/Electrolux
vacuums24x7.com/ElectroluxParts

There is no replacement for the dust container in these units. You would have to get an entire handvac which costs more then a full unit.

www.stickvacrecall.com

Sorry for the delay. https://www.google.com/search?q=Electrolux+1623+motor+wiring ..

This will happen if the bags are either incorrectly fitted or are non genuine bags that are not within the tollerance, size wise, for the machine.

See position of switch in the manual. It may possible, mains wires are sort that is by passing switch. Use Of Standard Attachments; Operation - Electrolux 2100 Instructions Manual [Page 6] ' ManualsLib

normally the battery gives up in this vacuum cleaners through my experience

confirm the charger first
use a voltage tester to check the voltage coming from the charger

the voltage will read from 12volts to 18 volts
depending you vacuum model.


If you the voltage is present then the battery is dead.

Question edited for full 'make model (what it is)'. Question moved from Washing Machines.

Trilobite error 18 Battery Fault?

RobotReviews http://www.robotreviews.com > chat > viewtopic May 25, 2011 - I suspect it happens when a discharged battery is very weak, and may be because the 15 sub-C NiMh cells of one battery are dis-equilibrated.

Messages D'erreurs; Fehlermeldungen - Electrolux ...

ManualsLib https://www.manualslib.com > ... > Overview manual Electrolux Trilobite Manual Online: error messages, Messages D ... our Customer Service, see page 18. The errors you can correct yourself are.

Trilobite error 18

Fixya https://www.fixya.com > ... > Trilobite Vacuum Sep 7, 2009 - Trilobite error 18 I looks like charging problem. Could you please give advice by myself. - Electrolux Trilobite Vacuum question. ..

Can't find the question for the Electrolux vacuum cleaner H5005, but I have one of my own: Where can I get a wheel for this model?

1. Start by removing the screws that secure the bottom plate of your vacuum. 2. Once the bottom plate is removed, you will find the belt inside, as well as the belt pulley and drive wheels. 3. Disconnect the belt from the belt pulley. 4. Align the new belt over the belt pulley and drive wheels so that the teeth of the belt match up with the grooves on the pulley. 5. Wrap the belt around the pulley and drive wheels, and then reattach the belt to the pulley with the supplied clips. 6. Reassemble the vacuum and you're done!

I would think there is a blockage in the hand vac hose.

possible motor failing [bearings] --fan damaged