20 Most Recent Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne - Page 10 Questions & Answers

Go to any local vacuum cleaner repair shop, they can match the belt

Might need a new belt

there's a reset button down on left side of powerhead in the black plastic at base that corrects the problem of that red light

Hey Nancy... Sounds like you have broken the roller drive belt...this is not hard to fix.. Check out this link..its for the belt you need... https://evacuumstore.com/p-7826-electrolux-epic-6500-belt.aspx?gclid=EAIaIQobChMI78fopqCb1gIVlQOGCh2__QQ9EAQYAiABEgKK1_D_BwE

There is not a replaceable motor filter inside the body of the vacuum. There is an exhaust filter under the cover on top which can be removed by pushing a little tab at the rear of the cover.

the dial sets the type of dirt you are vacuuming.Fine dust allow bag to fill before shutting down.The best is to turn it to the middle,this should allow bag to fill properly before shutting down...Chris

the dials refer to types of dirt.The higher the dial the heavier the dirt.This is for the auto shut off when the bag is full.The best setting is in the middle.If you are vacuuming up fine dust suck in some Kleenex before this will coat the bag and prevent premature shu toff.

flow this ?

i think it is unlikely that it is a wiring problem. i had to replace the canister control valve on my vac about 8mts ago so here is my research. http://blog.evacuumstore.com/post/2010/03/15/How-to-open-an-Electrolux-Canister.aspx http://blog.evacuumstore.com/post/2014/08/28/Fix-of-the-Week-How-to-Change-and-Electrolux-Control-Valve.aspx https://www.youtube.com/watch?v=IF546bOafe4 good luck tom Fix of the Week How to Change and Electrolux Control Valve How to Open an Electrolux Plastic Canister

Your description indicates an internal break in the wiring carrying the current to the sweeper motor, though it could be just a loose connection. The unit will need at least partially dismantling for testing and examination.

Schematics and repair manuals are only available to authorized Aerus Electrolux service techs. They no longer print the manuals, instead making them available through software, again only available to the computers at the Aerus stores.
The reason for this is obvious. Making them available to the general public would mean less work for the techs, thus less money for Aerus.

Electrolux does not make their service manuals available to the general public or non-Electrolux service personnel.<br /> It

Check the afterfilter. If it's dirty it can cause this. Try turning the vacuum on with the filter off.
If this doesn't help, the problem is probably with the Control Valve Assembly, or a tube connecting to it. This is the part that the dial connects to. The tubes often get clogged and need cleaned periodically, especially if generic ("made to fit") bags are used. The CVA itself may also be worn out or broken.
For cleaning, repair, or replacement, the vacuum needs to be taken to the nearest authorized Aerus Electrolux store. The service tech should also do a thorough cleaning and, at your request, preventive maintenance on the vacuum.

http://www.aerushome.com/storelocator/

I assume you're referring to the 1590 Aerus Electrolux Central vacuum? if so,and you're sure it's not a "breaker" issue at your breaker box and the reset doesn't work, chances are either the relay board inside needs replaced or more often, the motor itself if it's over 15 yrs. old. This is normal for motor replacement. I do replace them for my customers. Hope that helps!

I have no idea just what reverse suction would be or how to get it from ANY vac. If you're looking at getting the blowing air from the vac instead of suction, then simply move the hose from the suction end to the exhaust end.