20 Most Recent Whirlpool 30" Self-Cleaning Freestanding Gas Range - White-on-White - Page 6 Questions & Answers

F3 - E4 Oven temperature sensor (RTD) opened (lower oven, if double oven). You will have to replace this failed sensor to restore normal operations. If your oven is a double version, it will be located in the lower part. If its a single range, it will be located in the oven compartment. The Oven Temperature Sensor has failed.

Please rate and god bless:)

The door hinges have most likely been hyper-extended and need to be replaced as they are not longer holding the door closed. Or it is possible the door gasket is loose preventing the door from closing all the way.

because it ******* hates you; you dumb *****

it's telling that your ***. Sorry :)

Remove oven racks and look for two screws in the back on the bottom. Remove screws and lift out oven bottom. Do not use self clean.

On your model it should mean a defective door latch switch.
It will have to be replaced.

f-5 is a defective door latch code.

jdelvecchio5Does the igniter (glow bar) come on whenever the bake function is selected.?

If the glow bar does not come on the safety valve will not open - no bake burner. check the electrical harness first then Try changing the igniter (glow bar first) before changing the safety valve/regulator.

Check both gas valve solonoids for 216 ohms [blue broiler wire to the orange common and red oven wire to orange common] both must be ok.

Check oven temp sensor for 1080 ohms.

If above are ok then the problem is either the spark module or the control board.

Since the gas valve was not opening and there was not ignitor sound I replaced the spark module for about $90. You have a 50-50 chance of being right.

My range is relitively new and I'm haveing an oven light problem which I traced to the control board so I may replaced this board to for about $200.

HS

Sounding like your hot surface ignitor is getting bad. What I would like for you to do is open the oven and take the bottom panel off. This is so you can see the hot surface ignitor. Turn the oven on and look at the hot surface ignitor it is down on the bottom right next to the burner assembly. Does it start to glow and turn cherry red? This ignitor isn't too hard to replace couple of small screws and two wires. Will have to cut the wires so disconnect the unit from the 120 volt plug. Now if it starts to glow and get cherry red hot then the gas valve is sticking and it is the one going bad. That is a little tougher to replace. Turn the gas off at the source and get your wrenches unscrew the gas valve small space so if you want remove the door by just pulling it off the hinges.

If unit is old and you don't like it anyway maybe santa would be good to you and replace the stove oven. The gas valve is about 60 bucks or so and hot surface is about 20 bucks. let me know how it turns out.. ken

does it flip the breaker when it shuts off?if so sound like a short somewhere. i had kinda the same problem with a ge and it was the oven light was touching the panel and shorting out.

the burners on my magic chef stove work but the flame is not as high as it should be on one burner. I switched the top of the burner with another and it did not solve the problem.

Never ever use the Self Cleaning Feature. Its main function of to break things like elements, door looks and frazzle control boards. That keeps the maker is steady sales of spares. My old Ge Stove is from the mid 1970s. Of course they don't make them like that any more. They are non-electronic, so only elements can fail. You can check elements for continuity with a multimeter and replace them. If you fancy a new one, get one but never use the self cleaning feature and it will indeed last you 30 years. Bake elements https://www.google.com/search?q=Whirlpool+stove+bake+element ..

Never ever use the features of a Self Cleaning Oven. We see the damage they do here on Fixya, and the worst is the door not unlocking, and the most expensive is when they fry the mainboard. They all have a door interlock. If you were to open it when it was running, it would frizz your eyebrows!

Why You should Never Run A Self Clean Oven Cycle & ...

General Appliance Service https://www.generalappliancesvc.com > why-you-shou... Jan 29, 2020 - A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters with an extremely high temperature (932 F° or ...

Self-cleaning oven

Wikipedia https://en.wikipedia.org > wiki > Self-cleaning_oven A self-cleaning or pyrolytic oven is an oven which uses high temperature (approximately 932 °F (500 °C)) to burn off leftovers from baking, without the use ... ‎Pyrolytic process · ‎Alternative technologies · ‎Catalytic cleaning

Self-Cleaning Oven: 6 Reasons to Stop Using Feature ...

FIX Appliances CA https://fixappliances.ca > 4-reasons-stop-using-self-cle... A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters at an extremely high temperature (932 F° or 500 C°) to aid in ... ‎How Self-Cleaning Ovens Work · ‎Major Parts Damage ..

if wiring ok possible weak ignitor

Whirpool Self Cleaning Oven Instructions Hunker Please provide us the model number if you can.

Check the elements for continuity with a multimeter. Sometimes the connectors draw too much current and can burn out as well. Both are easy tests. A runaway temperature can make elements fail because there is no thermostatic control, they just glow bright yellow..

error f1 is shown when there is a problem in the control panel

Ed,Check here and watch video.https://www.repairclinic.com/ProductDetail/655475?i=178I entered your model and there's 4 diffrent ones PS1 PS2 PS3 etcso if this isn't it ck out the others on their site.Best to you.another site with video..under the part picture..https://www.appliancepartspros.com/whirlpool-elmnt-bake-wp9755770-ap6013936.htmlcopy n paste link.

Greetings, This might indicate a bad keypad or that the cable connecting the keypad to the chip board within your whirlpool has come loose. You might need to work with whirlpool to see if they keypad needs replacing or if the internal chip board itself is faulty. Thank you.