20 Most Recent Whirlpool 30" Self-Cleaning Freestanding Gas Range - White-on-White - Page 5 Questions & Answers

I have good news for you! You have a bake element that has gone out and it's a very simple repair. It will save you a ton of money if you replace this yourself.

Check the bake ignitor (glow bar attached to the burner). If it does not glow at all, but the voltage is supplied to it - replace. If it does glow, but draws current less than 3A - replace.

you may need to replace the bake ignitor. if it is glowing orange and not white, it isn't hot enough to light the bake. hope this helps

turn the gass off
find the gas valve on the back wall
unscrew the top
and replace the top with the part from the kit
if you have orrifices you will need to replace those
they go straight down the center of the burner

The only thing I can offer is this: Most electronics cannot recover from the extreme 900 degree temp of self clean cycle. It is therefore recommended not to use the self clean on newer models. Why not get some oven cleaner and do it the old fashioned way? If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

It sure can. Whirlpool has some wonderful appliances and their ovens have a very large capacity for your Thanksgiving turkey or what ever you cook. The best of luck to you and enjoy your huge new 30" oven.

Push Bake or Broil It comes up at 350 you can put in whatever temp you want if need different,then push Start when done push Cancel 

klbingman is a deadbeat who uses advice from fixya, and then does not pay. Avoid this bum

yes

No adjustment. Could be bad temp control unit or bad oven temp sensor. You would have to purchase a repair manual and test the current flow to and from the circuit. And then testing the oven temp unit with multi-tester.

in my opinion the oven is too big i have the eeb6500.5 and i swear buy it, i have seen many a 9600 come back from a customer either faulty, unrepairable or just not wanted if you want my opinion dont buy a eeb9600 or a eeb9800

Make sure there's power getting to your range, oven or cooktop. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power with a voltmeter or by plugging something else in.

If all check out ok with all the above, replace the ERC

Press and hold BAKE pad for five (5) seconds. Current offset, if any is shown in 3-digit display. CAL is shown in 4-digit display (3 digits on right).

Pressing the UP pad adjust the temperature in 10 degree F increments in fthe following sequence: 0, 10,20,30,-30,-20,-10, 0 and so on.

Press START/ENTER pad to activate the desire tempature adjustment. If the START/ENTER pad is not pressed within 5 minutes, adjustment is ignored.

I wired the oven to a different socket temporarily to check it and all the display lights came on immediately so I assume every thing else will work on a permanent supply.It is in fact a supply problem at the oven supply point and the electrician who rewired the house is coming tomorrow to solve the problem hopefully.

Ok, your mixture is to rich at this time. you will need to access the gas pressure regulator and adjust the air to fuel mixture. add a bit more air and back off of the fuel a bit. this will correct this issue.

depending on the model, this may or may not be an option so, if you cant access the regulator and the burner assembly is not accessible as well, i recommend calling the local gas utility service tech to preform this adjustment. This rich mixture is very dangerous for you and your family and i suggest that this be corrected asap for you safety.

Please rate and god bless:)

most likely you need the ignitor/glow bar. to test you need a clamp on amp meter to see if you have 3.0 to 3.3 amps, if it glows and doesn't light the ignitor is too weak to open the valve. get a new ignitor from a parts dealer and replace, make sure to put a drop of dish soap on the screws holding the ignitor to the burner, the soap will lubricate the threads on the screw so it doesn't strip out. hope this helps.

Electric range normally takes 50 amp breaker. Are you installing new line for this range? Normal practice is seu aluminum cable #6/ 3 conductor

Get rid, you do not want to try to fix this. Very dagerous. It could set your house on fire.