Top 20 Whirlpool Duet 7.0 Cu. Ft. Super Capacity Plus Electric Dryer Questions & Answers

when you unplug it you're resetting the computer board just like your house computer does,so if it helped by unplugging it i would have to say the board is bad and needs to be replaced.next time send the model number off of the machine

Dryer Makes Noise

Hello. First, turn the power off to the dryer or remove the power cord from the AC outlet. Next, locate the 2 screws in-between the upper and lower front panels and at the bottom front of the dryer--there will be 2-3 screws, usually 1/4 inch hex head, and remove them--use a magnetic nut driver, it makes it a whole lot easier! (note:sometimes, to replace the panel, you have to push up on the bottom of the panel hard to get the screw holes to line up again.) Set the panel aside. Open the dryer door and remove the lint screen from the holder. Close the door. Next, notice the blower housing cover, pic 3, #45, lower left corner. There should be 3-4 screws holding the cover to the blower housing. Remove the screws and cover--use caution--most metal edges inside a dryer are unfinished and razor sharp--akin to putting your hand inside a box of razor blades(ask me how I know this, lol). Remove any lint build-up inside the cover with a vacuum. Again, using a vacuum, suck out any lint from inside the blower housing and fan as best you can. Take care to not damage the fan blades! Now, try to remove as much lint build-up as you can with the vacuum. Be especially careful when vacuuming around the mouth of the heater element. Do the best you can. At this point, re-assemble the dryer using the reverse of assembly. If there is still a lot of lint inside the cabinet and you can't reach it--STOP! In order to remove the remaining lint requires removal of the front bulkhead(large metal plate that supports the front of the drum), drum belt, and drum from the cabinet. This is INVOLVED and can be very difficult to re-assemble if you have never done it before. Call for service. I hope I helped you!

Whirlpool duet sport F21 error code fix - YouTube

? 4:39 https://www.youtube.com/watch?v=qQTvBSnEWsI Feb 22, 2010 - Uploaded by heli400 Also note TROUBLE SHOOTING MANUAL IS TAPED TO THE ...I have replace 6 detergent ben hose 1 motor the membrane on thebuttons .... I've owned the washer for 6 years and I never knewthere was a filter underneath!

Whirlpool & Kenmore Dryer Repair #02 - Won't Start or Run ...

? 7:29 https://www.youtube.com/watch?v=SPRqKVE8JfY Oct 21, 2011 - Uploaded by canyonman1963 I have a Whirlpool Duet MOD GEW9250PWI It's not making any noise, ... only" I've unplugged it and plugged it back hoping it would reset it. ... The service man I use stated it was the motorgoing bad, the smell of ... i checked the door switch, it was fine too i believe. so thermal fuse ... There still is not start up.

Suggest the following.

• Check drum light. No light defective door switch. Light yes one leg of 220 circuit OK.
• Be very sure motor doesn't start when you set to run. Belt may be off the motor and motor is very quite. Fix belt. Motor may be stuck or failed listen to hear if it is buzzing
• When pressing start button listen for distinctive run relay activation. If when the start button is depressed I would expect to here the relay.
• Motor run circuit relatively simple. The drum motor and blower are one assembly.

Check the door interlock switch. You should be able to hear it click as you open and close the door. It is easy for it to snap out of place on some models. You can operate it by hand to check the action. Hope this will help

no, but there is a thermal fuse, normally located on the blower duct, near the blower wheel. More than likely, that's the issue if it doesn't start.

If you have a similar conectio as mine, you can't

Sounds like a main control issue. I would call a service technician for further investigation. Try shutting the breaker off for 10 minutes or so and see if this corrects the issue.

Bottom panel. But you shouldn't be able to put harness connector in the wrong terminal. The normally all have their own special cut in the board or they will be color coded.

Not likely such a thing. The funny shape probably has something to do with the air passages.

you have a bad computer board http://www.fixya.com/support/t24940167-dryer_flash_f01_kenmore_dryer_model

not a good model number GGW900wli send model number again,don'tt know what that code is in diagnostics,what is the problem with the dryer

think thats a thermal fuse gone bad

i'm sure you already found out that you have or had a bad thermister located on top of the blower wheel housing,just answering this in case somebody else has this problem.e1 error code is bad thermister

No way to tighten other than replace belt, or new tension spring.

Check for a reset button on the back.

Hi Is good you start from wright leg Is probably limit sensor (not expensive) and next program board (is expensive). No error codes?? Check also outlet at wall where is connected vent pipe. Good luck.

On a 4-prong power cord you have 2 hot wires, one neutral wire, and one ground wire. On a three prong cord, you have 2 hot wires and one neutral/ground wire. The difference is the on four prong the neutral wire goes to electrical neutral bus in the breaker panel and the ground wire goes to the ground bus in the breaker panel. Since the neutral and ground buses, although separate, both go to physical ground, on a three-wire setup, you are just putting the neutral and ground wire together, Most dryers actually have a place at the pigtail connection to do just that.

Hi Is three sample resolution : 1 electric cable broken 2 pushed bottom broken 3 thermal fuse broken Check cable ,change pushed bottom open the standing cover , exchange thermal fuse open back dryer cover. Usually is the fuse.