20 Most Recent
Whirlpool Duet 7.0 Cu. Ft. Super Capacity Plus Electric Dryer - Page 6 Questions & Answers
Dryer stop running, power is on
Hi
I
believe that everything else is fine rather it is the thermal fuse that is
located inside the rear panel to the exhaust duct that is bad and should be
replaced. If you want you can test this fuse for continuity and if it is bad
then it should be replaced, as it cannot be reset. If the fuse is fine then it
can be due to the control board that is bad and should be replaced.
Hope this helps...please post back for further assistance.
Daniel
Dryer works well for couple
sounds like it maybe a problem where you might have to check your exhaust to outside make sure all is clear of lint if clogged unit won't work.
Dryer is not heating but otherwise ok
Hi,If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly.if you dryer is gas check out this
gas no heat tip....If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check outthis
electric no heat tip...heatman101
I have a Whirlpool Duet
Hi,
There can be many reasons why your dryer will not start or turn...
The most common causes are the belt breaking or jumping off, or the motor goingbad...
Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...
Dryer Repair - The
Dryer is not TurningDryer Repair - The
dryer will not startheatman101
It is installed in my apartment in a small room
The dryer is designed to be vented outside therefore there's no way you can eliminate the humidity being introduced other than designing or installing a condensing system that would effectively extract the steam and turn it back into liquid. This condensing system must be constantly cooled to effectively to function as such.
Increasing the depth of the water may reduce the humidity being introduced but not significantly unless it is constantly cooled or deep enough that there will no temperature thereof during the entire drying cycle. The water loses its condensing ability as the dryer runs due to the consequent increase in the temperature thereof. Thus, there's a need to device a way to introduce fresh and cool water as the dryer runs in order to maintain the water temperature and extract as much steam and turn it back into water and be collected for disposal.
It is highly recommended to install a ventless dryer in locations where there's no possible way to install a vent. Ventless dryers are equipped with a built-in condenser that turns the steam back into water and dispose it to the drainage like a washing machine.
MY VENT PIPE IS REAL
Hi,
The
cycling or operating thermostatis often the problem when a
dryer runstoo hot, but there are also other things that can make it run hot also.
Here is a tip that I wrote that gives more details about
why a clothes dryer will get too hot.
Clothes Dryergetting too hotheatman101
Cannot be started and the status light "control
Take a good look on the control panel on the right ..It has a button that says press for 3 seconds for to lock ..Im not sure on your model ...but all models have a control locking button ..It may be the start cycle one ..If it is ..you have to press he button for 3 seconds and will unlock the controls ..
This happens when you try to make it start the cycle and hold the button on ..too long ..
All the lights come on
Hi,
There can be many reasons why your dryer will not start or turn...
The most common causes are the belt breaking or jumping off, or the motor goingbad...
Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...
Dryer Repair - The
Dryer is not TurningDryer Repair - The
dryer will not startheatman101
Dryer thermal fuse blows after one load. Cleaned
Many times this is due to the internal passages of the dryer being clogged, especially
around the blower assembly and narrow ducting areas of the machine. I would
try a shop vac with the narrow extension and a refrigerator brush available at
the big box home improvement store. Hope this helps.
Dryer gets too hot
Hi dangv1...
Check and clean if necessary your vent hose.
If you vent hose "seems" to be clean then,try running the dryer with the vent hose off and see if the dryer is not running hot anymore.
Make sure your lint screen is in place and has no tears or holes in it and is still firmly attached to the frame.
If you are running too hot you are not moving enough air thru the system.
It could be that the fan blade is plugged up.
The problem could be a large lint ball build up in the center of the fan or a sock,thin pants,a pen,etc. that has gotten into the fan by falling down the hole where the lint screen is normally inserted.
You have to find the air restriction to solve the problem.
It also can be a loose or worn out blower wheel/fan.
Please take time to rate me.
F70--What does this code signify?
F70 is "Central control unit heart beat failure" No communication is detected from the Central Control Unit to the User Interface. (In english, this means that the controler unit mounted in the bottom of the machine, probably in a plastic cover, has stopped talking to the control panel on the front of the machine where you push the buttons).
You need to take the top off the machine and check that the wiring harness between the 2 units is intact and that the plugs on the ends of the harness are firmly in place on both the Central Control Unit and the User Interface. If this fails to fix the problem, then the action indicated is that if the drum is rotating while this error is showing, the user interface is faulty and requires replacement. If the drum is NOT rotating while displaying this error, then the Central Control Unit should be replaced.
Sensing light on. Dryer not running. In all
This
problem is commonly caused by a blown thermal fuse located on the
blower housing behind the bottom panel. Remove the bottom panel then the
lint duct and check continuity of the thermal fuse. You can also bypass
the thermal fuse for troubleshooting purposes. Check for blocked lint
filter and restricted vent system if the thermal fuse is indeed blown
then replace it including the thermistor. Click on the link below for
detailed troubleshooting of this common problem.
Kenmore Elite and Whirlpool Duet Dryers Not Starting
Dryer Not Starting
You
don't have to accept or reject this post in order to add comment or
information. But accepting the solution
should you find it helpful and/or informative will not stop you from
posting comments or additional information. You can still communicate with the expert should you need further advice regarding the issue stated herein.
Will not get hot. just blows cold air. was
Hi,
If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly.
if you dryer is gas check out this
gas no heat tip....
If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat.
check outthis
electric no heat tip...
heatman101
Not finding what you are looking for?