Logitech Harmony 510 Advanced Universal Remote Control - Page 4 - Answered Questions & Fixed issues

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Some buttons of this remote control won't wotk with this TV.

it will depend on the remote--aspect, or zoom etc. The owner manual for the set should explain all the options---if do not have the manual Google the model number with "manual" and try to locate it.

Dear Sir:Please go to the next web for to search your code:www.fitness.manualsonline.com and download for free you code, and reset again for fix it. sincerely. God bless you.ernesto cuadramanagua, nicaragua. c.a

http://download.cnet.com/logitech-trackman-marble-serial/3000-18491_4-76207.htmlhttp://download.cnet.com/logitech-usb-trackman-marble/3000-18491_4-69788.htmlhttp://download.cnet.com/logitech-usb-trackman-marble/3000-18490_4-69758.htmlhope one of these helps you

Make sure the charger has power and recharge the remote. That should fix it.

Hello,

Safe Mode is a diagnostic tool in the Remote used for troubleshooting purposes. If the words "Safe Mode" or "Safe Mode Requested" appear on the remote, complete the following steps:

1. Ensure the Remote is in "Safe Mode Requested" by taking out the batteries, and disconnecting the remote from the USB cable.
2. Hold down the Off button and plug the remote into the USB.
3. Continue holding down the Off button for another 10 seconds. The remote should then display the words "Safe Mode Requested".
4. With the unit in "Safe Mode Requested", re-install the firmware by clicking Support on your home page.
5. Click Firmware in the Downloads section and follow the online instructions to upgrade the firmware.
6. Once the firmware upgrade is complete, click Update My Remote.
7. Insert new batteries into the remote.

NOTE: Ensure the new batteries are all the same brand.

If the above doesn't help, please let me know for further directions.

Good luck.

Change your batteries out for a fresh pair.

I suggest check in this link and select the right model: logitech.com/en-us/downloads/universal-remotes

Hope helps (remember to rate this answer).

I found 15 search results for hotkey errors. The hotkeys are like The "Alt", "Esc", "Ctrl", etc. The easiest fix I can think of would be to try another keyboard since they are so cheap. The other solutions are likely in Control Panel under mice and keyboards.

Try cleaning the contacts which connect the key plates to the circuit.

What you need to do is make sure the batteries are in correctly, go to http://myharmony.com in Firefox or IE8, and click the button that says "set up my remote" in the middle/left area of the screen. The website will show ask you to log in and then show a load screen. This is when it will ask you to plug in the remote. The whole process from here on out is done from your browser. Its actually quite easy, I just set up one of these remotes yesterday and it works great.

Hi. You can find one in the list here:- http://shop.ebay.co.uk/i.html?_trkparms=65%253A12%257C66%253A2%257C39%253A1%257C72%253A4341&rt=nc&_nkw=Harmony+880+battery&_trksid=p3286.c0.m14&_sop=15&_sc=1

Wireless mouse will not work with linux OS. What is your OS. Is the OS listed in your mouse system requirement. Please use a compatible mouse.

Universal remotes are so cheap, these days, save the batteries and get a new universal remote. It won't take you long to enter the codes for whatever devices you have. The remotes start at $4.00 - $32.00.

hi sir
please be more specific about the problem you post so I can help you.

You can try this codes If you are using SKY
065 742, 0063, 0065, 0471, 0584, 0743 ,1963 ,0065 ,0584

It depends upon your sound card capabilities. If you open the Volume/Audio Mixer via the notifications area, you should be able to call up the settings. Some (not all) cards allow for the simultaneous enabling of both headphones and speakers via a setting in that area. The predominant default, however, is not. The assumption of course is that if you're using the headphones you don't want the speakers.

Hope that's helpful.

That's definitely not a good sign..... I can help you with this but need to know, what model of remote is this? Probably a logitech harmony? Do you know which one?

Thanks
Tim

There are a number of reasons that this has occurred.
The simplest is that the batteries are low. Change the batteries first. Batteries last 2-3 months before they need replacement.
Try reprogramming the remote. Before you reprogram make sure that you have the latest firmware loaded from
http://www.logitech.com/en-us/440/5874?section=downloads&bit=&osid=1
One of these solutions should correct the problem. Let me know.
Thanks.