Frigidaire GLTF1240A Front Load Washer - Page 8 - Answered Questions & Fixed issues

On occasion, the manufacturer will in include paperwork inside of the back. You would have to remove the rear cover or panels.

Any error codes? Drain pump may be blocked.

Sounds like the water pump seal may be leaking.

This sounds like a similar fault I repaired on a Fisher Paykell top loader smart drive. It would fill up, start it's wash cycle (you'd hear the engine turn back and forth ) and a second later stop. It turned out that a position sensor on the motor had failed due to a small water leak. I'm unable to find the motor for your model of Frigidaire to see if there is a similar sensor or pick up module though.

I don't understand SHANE circuit board. IF you replaced the board, it has been upgraded and you need to order a new wiring harness for it. Please post the model number

Check if your water supply is coming in very well

You probably have a broken door (or lid) switch. You will need to replace it, as they are usually cheap plastic, easily broken, and not too hard to replace. God bless your efforts.

Hey friend, thanks for your inquiry!

I see off your post your Frigidaire washer is showing a "PAU 12" code. Typically "PAU" stands for pause which means the cycle has been interrupted. I would open and close the door to assure that there is a proper connection between the door strike and door latch. If you check that and still receive the "PAU" I would recommend a reset, which can be done by flipping the household circuit breaker off for roughly ten minutes. Hopefully this is helpful. -Matt

Then I strongly suggest you hire a repair tech.

I just had the same E90 code with my "good model" Frigidaire washer. It beeps 9 times, then pauses and repeats. Nothing worked as far as resetting, unplugging,etc. HOWEVER, I saw this guy's video and his "hairdryer technique" worked perfectly.
https://youtu.be/IhHvw2K7XO0
I took it a step further by not only removing the two screws from the back of washer and the top cover, but also removing the front panel w/buttons by taking off two scews in front top corners and three scews inside the detergent drawer (take drawer out first). I moved the hairdryer back and forth over all the wire harnesses for about a minute, plugged it back in and it beeped once like normal. Put it all back together and it's running a load of wash now!! Good luck.

Look for a utensil blocking the arm from freely rotating. Look in the blade that rotates too; it pumps the water to the arm that rotates.

Washer Electronic Control Board part 137006030 How To Replace It looked like you needed to replace the control board?? (very similar but not exact part number match) ... the attached video link shows how to do it. Helpful?? Good luck on your troubleshooting!!

Hi sir, i have frigidaire flcf07ggavd washing machine there is not getting water and after some time erro is coming e10. Please tell me about

First, have someone put the washer up in the air, level, and have someone look underneath it whilst it is running , to see if there is a hole in the plastic piping or the exiting hose. The reason I say so its that I have been in the appliance repair business for too many years to count, and I never, (up until now), heard of "routing it out" I would wonder it that job managed to rupture something. Also remember the exit pipe must always have a " U " bend that is higher than the back of the washing machine to retain the water in the drum. God bless your efforts.

The cost of the control panel will depend on the model. Usually these cost $200-300. However, the LOC often indicates a control panel lock is enabled. Try looking at the control panel for a button with a padlock symbol in a small font on or below the button or a pair of buttons connected by a line below the buttons with the padlock symbol in the line. Press and hold the button or pair of buttons for 10 seconds. On the Frigidaire FFQE5000QW, the buttons to press are Options and Select. I hope this helps. Please add a comment with the model number of your dryer for more accurate information on the control panel and the control panel lock. Cindy Wells

ok then the problem is much worse if the unit is belt driven and the motor can be heard still spinning you need a new belt installed about $150 plus otherwise if it is direct drive with no belt bad motor is the issue usually cost around $250 installed

Probably the belt. Ck out this site for the belt and how to replace inspect it. See item#3. https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/39-2-625403-/new/Frigidaire-Washer-is-making-loud-noise-FWS6973EW1 sorry for the late reply.

there is a bearing at the back of the drum that gets dry and sometimes the ball part wears down causing the noise you are hearing i would check that first

https://www.frigidaire.com/Owner-Center/Product-Support--Manuals/?productCode=FFBD2406NW Phone support: Mon - Fri, 8am - 8pm (EST) Sat, 9am - 6pm (EST) 1 (800) 374-4432 (EST)

if all the cycles are working when you move the timer to that function then the timer is not advancing, Replace the timer.