Frigidaire PLCS389DC Dual Fuel (Electric and Gas) Kitchen Range - Answered Questions & Fixed issues

Use a flat piece of wood or similar, to pry up the hinge to replace door. This way your fingers are not in the way, in case it snaps back. God-Bless!

Good Afternoon Mark, I see that you're having trouble with your Frigidaire range, model# PLCS389DC, shutting off in mid-baking, and will not restart until the oven has cooled. It sounds like it is either the temperature sensor, that is sensing a runaway oven temperature, or the control board itself that might need replacing. I suggest contacting you local authorized technician for further assistance. They will be able to determine what exactly is causing your oven to cut off in mid-baking. -Best Regards- WP

If you lock the oven to clean it you will not be able to get it open again;call a serviceman to repair your range; they will show you the correct procedure for setting the clean cycle.

I would have a professional check the control board to the elements. You could have a decent element, but a bad connection.

I suppose the door and hinge will need replacement. What is the exact model so i can get you a price quote for a replacement door including shipping and possible locations to purchase the door. Hoping to hear from you soon.

dorr hinges stuck

hi - theres a few things you can try out tp see how good or bad the problem may well be.

1 - use a match to light the burner as normal to see how good the gas flow is - press & turn the knob so it starts to ignite but using a match it should work ok.

2 - if the above works firdt time - then the problem lies with the puiezo electric igniter not gettingh a good path to earth.

- to fix this sort of problems one needs to give the burner metal parts a very good clean of the fat/grease build ups - you will notice when the ignitor arcs it most probably runs all over the place. Further where its arcing to the frame these areas need to be cleaned with those green rough cloth used to scrub pots etc. it will remove the grit and lightly expose a bit of metal to make a better contact for the system to flash over..


Cheers

Hello there:
These ovens have a internal reset device that needs to be reset
To reset it unplug the power cord from the wall then you will have to wait for 1 hour and after the hour is over plug it back in and you may hear a click within about 5 min and sometimes right away. if so press the cancel and now you will be able to open the door and resume normal use

The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%$%$^%#$

replace the EOC.

Be sure the timer (right most knob) is set back to MAN (manual) after cleaning in order for the oven to work.

I = E/R

Hi jgoogle this code itsays oven clock failure

Hi
Sounds like your oven heater failed. Not sure if its a fan oven or static type. If you hear a fan inside the oven then its classed as a fan oven

My oven is flashing code F10

If it is new fromt the factory, you many have the natural gas (methane) jets in the burners. You will need to check your bag of parts to find the propane parts (LP parts). LP jets allow a different fuel/air mixture to burn at the right heat. Check the owner's manual for details how to make the change.

Please rate me - Good luck.

http://www.applianceaid.com/fault_codes.html

this may help http://www.appliance411.com/faq/temperature-calibration.shtml

Have you checked the circuit breaker? If it's not lined up with the "on" breakers, move it to the completely "off" position then move it to the "on" position. If it keeps flipping the breaker off, call an appliance repair person. Check the internet for reviews of your local companies to find the best one.

Turn the breaker to the stove off for one minute, reset time and everything should work just fine. It worked for me.
Ken