20 Most Recent Canon PIXMA MX700 All-In-One InkJet Printer - Page 7 Questions & Answers

Hi Insert the USB connection on the USB flash drive into the computer's USB port. Once the computer recognizes that an external storage device has been connected, it will install the software for the drive. Then Windows Explorer will respond with what to do next. Select "Open folder to view files" when prompted in the Windows Explorer pop-up: "What do you want Windows to do?"If you do not get this message, access the USB Flash drive by accessing the "My Computer" folder from your "Start" menu. Then double-click on the "USB Disk" which is probably in drive "F." Also check this link to setup canon pixma:- http://support-sg.canon-asia.com/contents/SG/EN/0200065101.html http://ezinearticles.com/?Linksys-E1000-Router-Set-Up-and-Troubleshooting&id=4425461

Please get back to us if you have further query else please accept the suggestion.

dear david

try this

) With the machine power turned off, while pressing the Stop/Reset button, press and hold the ON/OFF button. (DO NOT release
the buttons). The Power LED lights in green to indicate that a function is selectable.
2) While holding the ON/OFF button, release the Stop/Reset button. (DO NOT release the ON/OFF button.)
3) While holding the ON/OFF button, press the Stop/Reset button 2 times, and then release both the ON/OFF and Stop/Reset buttons.
(Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green,
starting with Alarm LED.)
4) When the Power LED lights in green (and "Service Mode Idle" is displayed on the LCD), press the Stop/Reset button 4 times.
5) Press ON/OFF, press Stop/Reset 2 times
6) Press ON/OFF. Unplug printer and plug back in. turn on and should be cleared

oke , post me back
cropp

Go to this link on Canon's website... http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mx_series/pixma_mx700#DriversAndSoftware

Click on the Drivers and Software link, select your OS and download the drivers.

You'll be presented with the Drivers section (download the appropriate one for your computer) and the Software section for the various software packages for your printer. Download each of the ones you want to install.

These downloads are self-extracting zip files, to install them, just locate the files where you saved them and double click on each to extract and install the files. (Install the driver first).

Remove your printer from the PC and uninstall the printer software. Now reinstall the printer software and connect the Printer to be detected and installed. Check printer properties to see the ink levels.
Use head cleaning before a test is taken . It is possible that the head is not reacting to the need of the command , can be an issue with ink drying , can also be poor ink cartridge contacts/.printer heads

Hi and welcome to FixYa!

As a first course of action please try to remove the unit from power source and press hold the power button for 10secs. while unplugged to reset the system. After 10secs. please reconnect the unit to power source and turn the machine on. If it doesn't work, I believe that the unit has reached it's break point.

Hope this helps and thank you for using FixYa! Have a good one!

Don't refill cartridges, use genuine New Canon Cartridges in your printer as recommended by the manufacturer in the manual.

Also,Follow the procedure to reset the waste ink tank counter:

1. Turn off the printer ( "Power" button).
2. Hold the button "Resume" (red circle in the triangle), turn on the printer (click "Power") - an indicator light green.
3. Hold the "Power" button, release the button "Resume".
4. Not releasing the "Power" button, double click "Resume" and release both buttons.
5. Four times click "Resume"
6. Once you click "Power", to confirm the selected action (reset counter absorber). Click "Power" button again to turn off.

This problem may be caused by several reasons. Bad nozzle pattern,dirty film encoder,etc. Sometimes,perform printhead alignment may solve the problem or else you can set print or copy quality to HIGH.
Simply try to align the printhead or/and set print or copy quality to HIGH.

Recommended source:
Printer Clinic

Reinstall the printer drivers



If I've helped, please vote! Thanks!

go print -> properties -> page setup -> print options -> tick Disable the paper source setting of the application software -> hit ok and go back to "main" -> select the paper source that you want and hit ok ok and print

The installation file for Canon PIXMA MX700 All-In-One InkJet Printer is available in the link below with the following requirement of Win XP/2000/Vista...
http://download.famouswhy.com/canon_pixma_mx700_all-in-one_driver/ .
Thanks for using FIXYA.

Hi, 5C00 is a purge unit error, the purge is the cleaning unit on the right where the print head parks when shut off. If paper or something is caught in there you get an error, also ink build-up can stop it as well, a damp Q-tip will clean some of the ink away, if it doesn't help you need a new purge assembly.


Hope it helps.

Thanks for using fixya..........