20 Most Recent
Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher - Page 2 Questions & Answers
Water is not going through in the cycle
Good Afternoon Heidi, thank you for your inquiry!
I'm not certain I understand the issue the dishwasher is
experiencing. Is the dishwasher not
draining or there isn't any water entering? With this information I can better
address the issue. Thank you and I look forward to your response.
I have my kitchen wiht a padlock on the display I
Hello Ana, thank you for allowing me to assist you!
If you are receiving an error code E11, the unit may have a
shorted keypad. One of the best ways to determine if this is a false error code
is to reset the power to the appliance by either unplugging it or flipping off
the breaker for about ten minutes. If the error code persists, it would be
advisable to reach out to an experienced appliance repair to assist further
since more than likely the EOC (electronic oven control) will need replacing.
We recently had a power outage, the next time I
Hello Stacey, thank you for your post!
I understand the unit recently experienced a power outage.
First, let's try reprogramming the dishwasher. This can be done by either unplugging
it or flipping the household circuit breaker to the off position. It is
necessary to wait roughly ten minutes and then turn the appliance on. If
resetting the power does not correct the issue, your unit could be experiencing
a communication error with the control board, or a potential wiring failure. I
recommend reaching out to an appliance expert who is best equipped to pinpoint
the exact problem, which can often save you funds and a headache.
After power failure dishwasher only turns on eco
Hello Lena, thank you for your inquiry! Let's try
reprogramming the dishwasher by either unplugging it or flipping the household
circuit breaker to the off position. It is important to wait roughly ten
minutes and then turn dishwasher back on. Confirm that the door is properly
latched and try selecting a cycle. If resetting
the power does not correct the issue, it could potentially mean a number of
things: a communication issue with the control board, a potentialwiring failure, or faulty door latch assembly.
Because it could be a number of any one of
several underlying causes, I would recommend contacting a professional to
properly diagnose and repair the appliance.
Need manual
Good Morning Steve - I am happy to assist you, however
according to my database I'm not showing that Frigidaire has an error code FR
for a dishwasher or for any product for that matter. Could the error code possibly
be an ER, PF, FL or RF?
·
Typically error code ER indicates that the main
control board has detected a stuck key or a key pressed for more than one
minute.
·
Generally error code PF means that the dishwasher
has experienced a power failure and you should be able to resume the cycle.
·
Error code FL is advising you that the water
valve is in the open position.
·
RF indicates that the rinse aid reed switch in dispenser
is open and needs to refill the rinse aid.
Let's try resetting the unit by either unplugging it or
flipping the household circuit breaker to the off position. It is important to
wait approximately ten minutes and then turn on the dishwasher. If issue
persists, then I would personally contact a professional to accurately diagnose
the washer to determine the root cause to reduce the risk of unnecessary parts.
I hope these troubleshooting tips help you in some small
way.
Frigidaire gallery stove
Hello mnwpictures - Based on the symptoms you are describing the range may either have a faulty EOC (electronic oven control) or a potential wiring failure. Try resetting the range by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and then turn the unit back on. Does the control panel have a display? If the issue persists, I would recommend contacting a professional to proceed further. Most likely the EOC on the range will need replacing.
Install controller
Hello David - Regrettably, this is not a simply DIY job. Generally, qualified technicians often perform these complicated part replacements. Usually this type of information is not released to a consumer and very rare to find enough information to do it yourself. If I was in your position, I would personally suggest contacting a professional to accurately assist with the repair or installation of the part.
Leaks
Hello Emmitt White - Try unplugging the dishwasher or flipping the household circuit breaker off first. Wait approximately ten minutes and turn the unit back on. If the issue persists, it could possibly be a few things: faulty door switch, drain pump or main control board. In that case, a certified technician would generally replace the faulty part after proper diagnosis.
Upper spray arm broke off
I hope it did not break, only came off. I had the same problem. You have to unscrew the round part from the ceiling of the dishwasher, put the three pieces together, easy, and then screw the whole thing back. No tools needed. Top rack can stay on while working. It helps if the dishwasher is empty. If the threading is good, this should solve the problem.
Grinding during wash cycle
Possible that there is fault in the spraying unit or arm. It can also be due to faulty PUMP or a dirty filter which can CHOKE the pump.remove and clean the pump and filtercheck this link for tips :
spraying arm
Panel lights shut off when door closed. Have to set before shutting door is this normal?
Hello Pat Braley - The issue may lie with the door latch; a door switch is used to start and stop your dishwasher. It's a safety feature that won't allow water to flow with the door open. With a faulty door switch, there is a chance your dishwasher won't start at all. Dishwasher door switches are about an inch long. They are usually black but can be red. There are metal prongs on the body of the switch called terminals. Some door switches have two terminals and some have three. If your door switch is OK, check the timer assembly. This controls when and how long power is sent to other controls on your dishwasher. If these controls don't receive power, they won't work. The timer assembly contains a motor. Check this motor as well. It is often cheaper just to replace the timer motor rather than the complete assembly. My last suggestion is to check the cycle selector switches. These switches indicate cycles for washing, drying, and setting the temperature of the water. If one of your switches is the problem your dishwasher may also prevent the unit to start. Dishwasher cycle selector switches tell the timer which cycle to run by opening and closing electrical circuits. Most selector switches are six to eight inches long. They are usually black and have terminals. By testing each one of these parts with an ohmmeter you should be able to determine why your dishwasher is not working. It is possible for other parts to fail but these are the most common parts to check. If any proves to be ineffective, I strongly suggest contacting a professional to move forward accurately.
12/14/2012 10:17:23 PM •
Frigidaire...
•
Answered
on Dec 14, 2012
Fridgidaire pld4375rfc0 detergent dispenser not opening
Hi leeroyf - If the soap is not dispensing all the way out then usually the sprayer arms are not able to reach that area of the unit and door. I recommend making sure that the area is clean of dishes to try to prevent this issue because it sounds like something is blocking it and that the dispenser door is not stuck. Using the correct of amount of soap is also helpful. However, if problem proceeds then I suggest contacting a professional to move forward accurately since it may be having an issue with the wiring connections to dispenser and control.
Not finding what you are looking for?