Top 20 Yamaha HTR-6030 Receiver Questions & Answers

did you blow a fuse

Have you tried the unit without ANY speakers or cables connected first of all?

If you have a skybox F3 or F5 it should be a straight connection from the red, white and yellow jacks to either the DVD, DTS/Cable, or DVR-In Inputs on the HTR-6030. The V series looks to be HDMI only, so connections will not be possible without some type of external converter. The FS series looks like most of them support composite video output also.

Shorted component/s at its power amplifier section circuit. Contact any service technician. If you wish to get some details; visit the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Hey, I read your question, it was good. My suggestion is that you buy a 5 in one sound system and you want to hang in your room in surrounded they you will see the sound will fade and also it is good for listening. If you want to know more about it then follow the site Internet Explorer 10 customer support IE 10 Support Internet Explorer Tech Support Number Help Desk

no on that model

No you cannot.

Check the wiring from the back to the speakers for shorts, if okay suspect the audio output ic's on the one side.

Speaker Cable

There is no setting that would choose one front speaker to work differently than the other. The amp or something in the audio path within the receiver is failing.

Here you will be able to find the owners manual:

http://usa.yamaha.com/products/audio-visual/av-receivers-amps/htr/htr-6030_black__u/?mode=model

If you provide more details of your trying to do I can assist you further.

some amps have a built is protection circuit, take it a local hi-fi dealer and get them to take a look at it

by press "EFFECT" button, choose Movies or Musics, Dolby digital, unit will play 5.1

Please don't panic and think that there is anything wrong with your Yamaha receiver. A lot of people are having this problem with set top box reception. Time lag / phase differences caused by satellite transmission can make your Receivers digital decoders go nuts !!!.The working principal is too complex to explain on this page. I have had clients call up and say on some channels only one speaker works in a 5.1 setup !!!!.You noticed DD and DTS signals are working fine.

Hi there,

It simply means to check your (sp)eaker cables. It is likely that one of your speaker cables is damaged or not correctly connected. This is causing an overload in the receiver and the cut-out indicates the receiver has gone into 'self-protect' mode, to prevent damage to the internal components.

This could happen if you have cross-wired + and - to one or more of the speakers. It could also be that a cable to one of the speakers has been partially severed and +/- are shorted together or it could be as simple as one of the speaker connections having become detached. Speaker connections are polarised positive + and negative - the same as your household electrics and need to be wired to the correct poles.

To fix this problem, you should initially check all of the speaker connections at both the receiver and speaker ends. Make sure everything is properly connected and that + and - on the receiver are correctly wired to + and - on all speakers. If all of the connections are correct and the error message persists, disconnect each speaker one at a time, reset the receiver and test again.

If you disconnect a particular speaker and the error message no longer appears, you have found the cause of the problem. Examine the cable for any sign of damage and replace the cable. If there is no visible damage, it is still advisable to replace the cable for this speaker as damaged cables are not always visible to the eye.

Please check all of your speakers as above, then let me know if you need further assistance. The message could be erroneous and may indicate a fault with the receiver.

Hope this helps.

Regards,
BElectric.

sell the bose sub, buy a nicer yamaha sub, enjoy the 200 bucks you have even after you buy a new speaker.

You can over write on the old code any number of times. Just follow the first three steps and enter the new code. The last code you enter will be saved in memory.

please choose front SPK channels from A, B or Off by SPK button near headphone Jack. if you choose Off, then front A and B don't plsy sound

Hi,
We just discovered in chat session that receiver is defective and left speaker has no sound, please take it in local repair shop for visual check and repair.
Thanks.

Hi there,

If you only have sound from the front left and right speakers when it's set to STRAIGHT, it means the audio source is only 2 channel stereo. As the audio source is from Blu-Ray, the audio should be HD if you are using the correct type of audio cable.

I really need more information from you to give a definitive answer. If you are only using a RCA type audio cable (red/white plugs) from the Blu-Ray to the Yamaha receiver then you will only get left and right front channels on the STRAIGHT setting. This receiver does not have HDMI, so you really need to be using a digital optical audio cable to get true 5.1.

Please can you let me know how the BD player is connected to the Yamaha receiver if you need further assistance.

Thanks,
BElectric