Top 20 Frigidaire 30 in. Electric Gallery Series Self-Cleaning Double Wall Oven - Page 5 Questions & Answers

Okay,
1, check your power, locate your breaker for the range. turn the breaker off and turn it back on.
Your Range it is electronic control on the Oven but not the Stove Top heating elements.
After you reset the breaker and it still not work.
Please let me know more about the unit.
When you purchase.
How/when it happen.
What is the indicator showing.

[email protected]

Frigidaire dishwasher will not work at all it has PF blinking

Hi, i would check the pressure switch and its connection as well. either the switch is malfunctioning or the wires and connectors are corroded. simply replacing the wires or switch will fix this issue. the switch is usually located on the rim of the inside of the oven door. it will make contact with the oven door and as the oven door closes, the pressure switch is depressed inwards, thus, opening the circuit and cutting power to the light.

Please rate and god bless:)

If the element only works partially or not getting red hot at the "Hi" setting, the problem might be with a burned out receptacle that the element plugs into. If this is the case, replace both the element and the receptacle.

You can usually tell when the element itself burns out. It might have small holes or bubbles on the coil. Replace the element, if found defective.

Yes needs a new element.they burn out. easily.you know this because they sell them seperately.its there way to make money off of you.anytime they sell you something and the parts are readily available especially sold seperately you know its going to need to be replaced eventually..If you replace 1 replace them all to avoid furthur issues.

get it from "Appliances Parts Pro's" .com

Sir,
Check out this link

suggest to reset it by shutting off both main breakers to the stove , wait for one minute and switch breakers on again.

Thanks Good Luck
Appreciate to rate as "Fixya"

Whithout knowing the model number in general it takes several hours for the cleaning cycle. My oven takes approx. 4 hours to complete a good cleaning. On my own oven, you can set the timer for as long as you want. Do you have an owners manual? If not, you can find one here...........
http://www.frigidaire.com/support/manuals.asp

my oven won't get hot - pilot or more serious?

i would say its a wiring issue so i would have to turn to the repair man

This is failed communication between the EOC and the temp sensors located in the oven. i recommend testing the EOC(break point test on the pins) for its operational value and the temp sensors as well. replace any component that doesn't register.

I would also inspect the oven temp sensors for welded harness and fouled housings.

In most cases, this will be a EOC issue.

Hi Ekahan512,

The "F10" error code caused by the runaway temperature.

The first thing I would check is the resistance across the oventemperature probe (aka oven temperature sensor) terminals at the EOC(electronic oven control) plug.

It suppose to be about 1100 Ohms at the room temperature.

If the resistance at the EOC plug is wrong, then measure the oven temperature probe resistance at the probe plug.

If it's wrong - replace the oven temperature probe. It's better to hardwire it, using a high temperature ceramic wire nuts.

If the readings at the EOC and at the oven temperature probe plug aredifferent - check the wire harness between the oven temperature probeand the EOC.

If there is nothing wrong with the oven temperature probe resistance - replace the EOC.

- The part number for the oven temperature probe is AP3704441

- The part number for the EOC is AP3776874

- The part number for the EOC overlay is AP3778486

Good luck.
Taran.

If both elements are not working properly then the problem is either the temperature probe or the control board.

Replace the temp probe first.

shut the power off for 30 mins at circuit breaker and then it worked after that.

The switch contacts have welded closed and you must replace the switch.

F9 code means Control has detected a problem with the motor door latch assembly Soultion: Check wiring, replace the motor door latch assembly if necessary

Change the input. It' on VIDEO and it's looking for a video input device, like a DVD player or VCR.

Hope this helps!!!

test

u can go to there site or type in the model numbers and/or the model it self and after that typ manual and it should come up on the intranet

do have the the seting set to air dry? or possible a sensor issue or maybe the heating element at the back has not bee connected or has shorted