Top 20 Jenn-Air Electric Double Oven Questions & Answers

Somewhere the control is not reading fan rotation could be encoders harness or control had this error once reset oven till I could return with control error never returned replaced control anyway

That's a normal condition. The fan runs until the heat is dissipated.

check breaker box make sure you are connected to the right load and getting sufficient power

Good luck with that!!! I had the same problem and scoured the internet for a solution. If you can find a used or rebuilt part you may be in luck. The thermostat on the left is a 6 pole one for the upper oven while the one on the right is a 4 pole for the lower oven 71001126. I doubt you can substitute the one for the other and give up the convection and self cleaning functions. Let us know if you find a solution or buy a new stove. Sears has a few 24 inch double ovens left, as the world is moving to 27 and 30 inch ovens.

Hello,

Here is a link to that installation guide for that walloven
https://www.maytag.com/digitalassets/MLPDF/Installation%20Instructions%20-%208101P423-60.pdf


GENE

Hello & Welcome to FixYa

This indicates an open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you want to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more than this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions. Kevin

Hi. Erorr 4d22 indicates that the control board isn't seeing the fan speed signal from the fan on that oven. It's the lower oven, right? Check the connection to the Fan and Control board, and if that's not it replace the fan. HTH.

your walloven is 220 volt hookup

Hi

Get to the fans (behind the control panel) and check the screens for dust. Chances are the screens are clogged with dust and need to be cleaned so the fans can move air for cooling better.

However most importantly eliminate the oven sensor plug at the back of the range and hardwire it using a high temperature porcelain wire nuts. Then locate the sensor plug at the control board and measure the sensor resistance. It is supposed to be about 1100 Ohms at the room temperature. Make sure there is a good connection between this plug and the control board. Also try to reset it by unplugging the oven and put it back after 30 minutes or .If the fan is not stopping then it is probably a wire that has a bad connection and feeds it with electricity when it's not supposed to. Probably the isolation went off from the heat and in this case you need to call a repair person to get it diagnosed.

Please get back to us if you have further query or else please accept the solution.

F5 = Watchdog and hardware conflict

Loss of relay drive circuit If this fault code cannot be cancelled, replace the oven control (also called clock or ERC).

Sometimes just unplugging the sensor quick connect and cleaning the corrosion in it fixs the problem. Replace control board (also called ERC or clock).

F5 indicates the control felt a loss of power. I generally check the oven sensor for resistance (1040-1090 Ohms @ 770F). If the sensor is within normal limits, the control is bad. Replace clock (ERC).

(see the following link) although it can sometimes be caused by a failed oven temperature sensor. The sensor should be checked before replacing the control. It should read about 1100 ohms when at room temperature.

- Kenmore 911.45565791 Electronic Control > www.appliance411.com/data.php?ap=AP3156070

- 911.45565791 Oven Sensor > www.appliance411.com/data.php?ap=AP2023670

Hope helps.

From JENN AIR FAULT CODES...

FC - Communication error between boards - Wiring harness or power relay board (PRB)

Hope helps.

Hi,

If your electric oven is taking too long to heat or just not heating up right, then check out this tip that will give more detail about your problem.Oven Problems Electric Oven is Heating Slowly or Poorlyheatman101

F5
Watchdog and hardware conflict
Replace clock (ERC).

Look at the hinge, their is like a slider bar to move or you remove the little cover plate, with the Philips screw..then lift the door up and out while pulling...

I WARN YOU, if you really don't need to remove the door don't, it is very hard to put back on unless you have had practice....

F1 touch pad / ERC test This simple test will help determine whether the ERC (Electronic Range Control or Clock) or the touch pad is defective when F1 error code is present.

Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).

Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.

1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.
2. Gain access inside the control panel.
3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.
4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.
5. Turn the power back on.
6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).
7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hi,

Here is a tip that will help you figure out why your oven will not shut off...

Electric Oven Problem Oven will not shut off

heatman101

Hi,
Seems like you found out the hard way what I wrote about in this tip...
Check it out it also contains some thing to try on how to unlock that oven..

Self Cleaning Oven Problem
http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101
Asker's Testimonial " Wish I had read this first. I never would have usedthe self cleaning option. Thanks for the info!! " - amymrocks

Hi,

This means that either the probe jack or the wires going to the probe jack have shorted out thinking there is a probe inserted even though there is not. You will need to replace the probe recepticle which comes with new wires to correct this issue. If you don't plan on using the oven probe, you can always clip the wires and tape the ends off as this will make it so that the board cannot sense the oven probe recepticle giving it a false reading.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Hi,
If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

Hello, Pull the unit out from the wall. Remove the panel at the rear off the controll console. Behind here you will find a tech sheet. Listed on this tech sheet will be all the error codes for this unit. It may be that this error code is specific to this unit.
If you have any further questions please feel free to ask.