nf shows up and washer stops
nF means that washer tried to fill but was unsuccessful. Water supply valves needs to be fully open. Lines may be kinked or screen by the hose hookup at the washer end may be restricting flow. Check to ensure the screens are cleaned by removing hose and pull screens and clean them then try the washer again
Posted on Jan 18, 2008
I have a silver samsung washing machine it is giving the fault code ..de ..close the door the door is closed can I reset the memory on it model j1453 thanks
i have samsung
6 kg WA80HAG silver nano
dear'
plz help me to reset washing
machine
thanks
Posted on Jan 08, 2014
I have a Samsung front Loader Washing Machine- Model J845 -nif there was a picture of where the belt goes it would be great. I have a new belt and i know if will be relatively straight forward to install but i didn't see where the very unprofessional unfriendly rip off service tech took the old one from so not sure exactly where the new part belongs...and i'm sure not having him come back out!!
Any instruction would be great.
Thanks
If you stand in FRONT of the washer, leaning over the top, the drive wheel is underneath the main drive motor, on the RIGHT hand side. Loop the belt over the drive motor wheel, then over the main pully, and it should be good to go!
Posted on May 23, 2008
my samsung 7kg front loader keeps flashing UE on the error code (spin cycle) and I can't open the door
UE = Unbalance Error
Laundry load is unbalanced, manually loosen any tangled laundry.
If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Unbalance error is cleared by POWER switch OFF and back ON.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
Posted on Sep 16, 2010
sud error showing what does this mean?
usually this alerts you to to much soap suds in the unit.run the washer with no soap this should clear the system and try and reduse the amount of soap you use
Posted on Sep 27, 2009
samsung washer wf218anb/xaa has code dc and wont spin clothes they are still wet
The DC error code is an unbalanced laundry error. Try putting less clothes in and if that doesn't fix the problem, then replace the hall sensor( located behind the drum, underneath the rotor).
Posted on Mar 10, 2010
washing machine won't drain. What does the hour glass symbol mean. It is defined in the owner's manual
From <http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx=419733&modelname=WF409ANW&modelcode=&session_id=V5mMmkpq72BqyQB5Lny5vwblqvWTyT6hLbGQypLMbhMpMhlQBdfJ!-943087853!1669102353!1442424460210&from_osc=&homeid=2217>: "The hour glass is displayed to let you know the washer's timer is counting down. This is normal, and does not require service."
Posted on Sep 16, 2015
nd error code (not draining) samsung washer can I fix this myself?
Hi from retired Englishman in SW France,
ABSOLUTELY!
Sorry but I do not know your particular machine BUT I would suggest as a first step that you clean the drain motor lint tray/filter. So many 'faults' are caused by blocked filters. The motor is unable to drain all of the water in the allotted time.
If you are unsure where the filter is, it is normally behind the front lower (kick) panel (or in some machines at the rear in an awkward position!) and held in by a round cover/knob.
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. If it doesn't work then the motor is malfunctioning!
Hope the filter is the problem and good luck!
John C
Posted on Feb 20, 2011
I have an error code that says nf
Hello & Welcome to
FixYa NF error in your washer is displayed due to no fill condition,
when the washer tries to fill but is unable to nf is displayed. Please check
the water inlet valve for any clogs and obstructions, you can also clean the
inlet to solve the issue. Please
get back to me if you have any other questions. Kevin
Posted on Mar 06, 2011
d5 error
Error code D5 OR DS is the same.Its mostly DS which looks like D5.
The D5 error is actually DS. The code means the washer thinks the
door is open or unlocked during the cycle. The door has to be checked.Is
it getting properly close/open.If its getting close/open then the
problem is related to faulty door locking assembly. But if its not
getting proper close then there is any blockage causing the door to
close or the door lock latch is faulty causing this problem.
Hope helps.
Posted on Jul 28, 2011
1,202 questions posted
Usually answered in minutes!
231 Questions
191 Questions
118 Questions
116 Questions