20 Most Recent Kyocera FS-2000D Laser Printer - Page 5 Questions & Answers

Call service message 6000 in Kyocera is a fuser error code. The fuser must have gone bad.

Regards,
Shrey

need to clean your cartrage. .. .

This is a fuser error. Install a new fuser.

Replace waste toner box.
http://www.kyoceramita.co.uk/index/products/consumable/toner_installation.-cps-12303-files-97992-File.cpsdownload.tmp/Toner-2000D.pdf

Here's the manual: http://usa.kyoceramita.com/americas/jsp/upload/resource/19873/0/FS2020D-3920DN-4020DNENOG-ADV.pdf

Go to page 65 for Network configurations directions.

Yes it is a fuser error.

6120 Abnormally high fuser thermistor S temperature

*35/37 and 45/47 ppm printers (EUR/USA model) only

The temperature of the fuser thermistor S detects 250°C/482°F or more continuously for 3 s.

Shorted fuser thermistor S.

1. Measure the resistance. If it is 0 ω, replace the fuser thermistor S.

2. Defective engine PWB.
Replace the engine PWB

When your reports paper jam for any reason, whether there is paper jam or not, most times you need to go thruogh paper jam clearing procedure to have your printer printing again. So please follow the procedure below:-

Clearing paper jam in a printer is simple almost seven step procedure depending on the printer. Paper jam is the term used to refer to the scenario where your paper fails to come out of the printer during the print process. When you send a document to the printer, normally the printer prints out the document on a paper; then you can pick up your printed copy. When the paper gets stuck in the printer, it is said that paper has jammed in the printer "paper jam".

Even if you are not a technical person, you can conveniently clear paper jams. All you need is to follow the set of procedures outlined below.

Put off the printer and unplug it from its power source.

Open all the covers/shutters on the printer (usually you will find one in the front or top and one at the back of the printer).

(If the printer is a DeskJet, otherwise ignore this step) Now pull out the cartridge carefully and place it on safe surface. (Be careful not to place it where it may slide and fall. This could damage the cartridge)

Site the paper that has jammed and pull it out in the opposite direction of its movement. Do not pull in the direction it was coming out. (Pulling the paper in the opposite direction is important for the printer's mechanism. Printer must be off). Never pull out paper from a printer when the printer is powered on.

(If the printer is a DeskJet, otherwise ignore this step) Return the cartridge gently and press it firmly inside so that you here it snap inside.

Close all covers at the top, front or back.

Power on your printer and you should be able to print again.

Good luck and God bless!

Please get the correct driver here : www.printcountry.com/drivers.asp
www.opendrivers.com/.../printers-free-driver-download.html
www.driversdown.com/driverslist/r_4_1.shtml
Regards, Jay__hcg6734e

Drum unit non- installing error
The drum unit is not installed or not
installed properly.
The drum PWB EEPROM does not communicate
normally.

Causes:
- The drum unit is not installed.
- Defective connection drum PWB (YC1) and connect-L PWB (YC3).
- Defective drum PWB EEPROM.
- Defective engine PWB.

Check procedures/corrective measures:
- Install the drum unit
- Check the connection of connectors drum
PWB (YC1) and connect-L PWB (YC3).
- Replace the drum unit
- Replace the engine PWB

Code 7000
Contents: Toner motor lock error A motor over-current signal is detected
continuously for 5 seconds since the toner motor is activated.

Causes: Lump of toner inside toner container.
Check procedures/corrective measures: Replace the toner container.

Causes: Defective toner replenishment drive system.
Check procedures/corrective measures: Replace the developer unit

Causes: Defective toner motor.
Check procedures/corrective measures: Replace the developer unit

Causes: Defective engine PWB.
Check procedures/corrective measures: Replace the engine PWB

Code: 6000
Contents: Broken fuser heater lamp wire
30 ppm model:
The temperature does not rise 1×C after
the fuser heater lamp has been turned
on continuously 5 s.
35/45 ppm models:
The temperature does not rise 1°C after
the fuser heater lamp has been turned
on continuously 5 s.
The temperature does not rise 1°C after
the fuser heater lamp has been turned
on continuously 10 s during waming-up
or at standby.

Causes:
- Poor contact in the fuser thermistor M connector terminals.
Check procedures/corrective measures:
- Reinsert the connector

Causes:
- Fuser thermistor M installed incorrectly.
Check procedures/corrective measures:
- Check and reinstall if necessary

Causes:
- Thermal cutout triggered.
Check procedures/corrective measures:
- Check for continuity. If none, replace the thermal cutout

Causes:
- Fuser heater lamp installed incorrectly
Check procedures/corrective measures:
Check and reinstall if necessary

Causes:
- Broken fuser heater lamp wire.
Check procedures/corrective measures::
- Check for continuity. If none, replace the fuser heater lamp

It sounds as if the printer is locked up waiting for the next cammand during a firmware update. I am assuming youe are not doing a firmware update from the DOS prompt of your computer; so disconnect your parellel cable and turn the printer off and back on; if you still have the error you will need to replace the control PCB.