Frigidaire (FEB30S7D) Oven - Answered Questions & Fixed issues
Unlock the oven door frigidaire Electrolux
IT should time out eventually. I am not sure if there is a way to reset it but if you hold the control lock button for 3 seconds (If it is Locked) and wait it SHOULD time out. I hope this helps to some extent.
7/9/2015 2:16:22 PM •
Frigidaire...
•
Answered
on Jul 09, 2015
•
2,456 views
How much clearance is required between the bottom
The installation manual does not specify.
(If you need a manual you can get one here:
http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man)
As an installer, without a manufacturer's specification, I would assume no specific clearance is required. Further, if you check the exploded parts diagram in the manual you will note that there is an insulating panel in the base of the oven. Evidently the oven has been designed to insulate the exterior panel from excess heating and does not require any minimum clearance at the base.
3/19/2010 1:51:22 PM •
Frigidaire...
•
Answered
on Mar 19, 2010
•
91 views
There is a terrible smell from the oven
I would need to be there to verify but if it is not an electrical odor then I would suspect a dead rodent, or if you have pets a mouse could have packed the space between the liner and the frame with pet food. I had one that had stored 20 pounds of dog food in there.
Eric
11/11/2012 10:40:55 PM •
Frigidaire...
•
Answered
on Nov 11, 2012
•
301 views
Oven coil burning hot on one side, popped and
It is probably the coil. If liquid or grease spilled on it, that would be a good bet. Coils can be easily replaced, and I would start there before calling a service man. Just make sure you unplug the appliance before replacing it, and then make sure that the new one is firmly plugged in before putting the plug back in. Don't use the damaged coil, it can (probably will) catch on fire if you do.
11/8/2009 3:47:48 PM •
Frigidaire...
•
Answered
on Nov 08, 2009
•
189 views
3 wires black white ground from box from oven red
the appliance is 220 volt and the box you are describing is 110 volt. You cannot connect to this box. You need a new 220 volt circuit ran from your main panel box to the appliance with a 220 volt 3 prong outlet box like an electric dryer uses or make the connections in a box without using the plug system
8/18/2009 12:10:47 AM •
Frigidaire...
•
Answered
on Aug 18, 2009
•
164 views
Fault Code F1
Frigidaire oven fault code F1 means the electronic clock control is bad and should be replaced. That is the electronic control board that shows your clock display and is also called clock or eoc, depending on your model.
3/2/2009 12:36:29 AM •
Frigidaire...
•
Answered
on Mar 02, 2009
•
1,393 views
My frigidaire ovens broiler came on, on high, when i was baking at a very low temp (170).
If your Frigidaire oven's broiler unexpectedly turned on while you were baking at a low temperature, it could indicate an issue with the oven's temperature control system. Here are a few possible explanations and troubleshooting steps:
- Incorrect oven setting: Double-check that you have selected the correct oven function and temperature settings. Ensure that you have chosen the "bake" function rather than the "broil" function. Also, verify that the temperature setting is appropriate for baking.
- Malfunctioning temperature sensor: The oven's temperature sensor, also known as the oven thermostat, could be faulty. A malfunctioning sensor may send incorrect temperature readings to the oven control board, causing it to activate the broiler unexpectedly. Consider contacting a professional technician to inspect and potentially replace the temperature sensor if necessary.
- Control board issue: The oven control board, which regulates various oven functions, could be experiencing a malfunction. If the control board is sending incorrect signals to the broiler, it may activate when it shouldn't. Consult a professional technician to assess and repair the control board if needed.
- Wiring or electrical problem: Inspect the oven's wiring and electrical connections for any signs of damage or loose connections. Faulty wiring or poor electrical connections can cause erratic oven behavior. It's advisable to have a qualified technician examine the electrical components to ensure they are functioning correctly.
Not finding what you are looking for?