20 Most Recent Frigidaire FGB24S5A Gas Single Oven - Page 3 Questions & Answers

Your average price range for a Frigidaire is between $560 and $800

It shouldn't be burning yellow and emitting soot at all;sounds like on of these possible causes-
(a)blocked burner airways(this can lead to yellow tipping and sooting on LPG powered appliances because insufficient air is getting through to the burner causing it;you can also get this effect on LPG barbecues say if dead insects or spiderwebs are in the burner pipes and airways after a period of storage),
(b)incorrect aeration being set when the burner was converted using LPG jets(too much gas and not enough air causing yellow flames/smells and sooting),
or (c) if you use propane cylinder gas a dicky or faulty regulator. I would get it looked at investigating all the possibilities I mention and taking action to correct this where necessary ie clearing the burner airways(if this is causing your problem), adjusting the aeration in the burners until you get a clear noiseless blue flame without any excessive yellow and sooting(but even after good adjustment you may find still get a very slight yellow tip without sooting at the top of the flame;this does happen with propane gas and there is a slight tendancy for this to happen more often with butane-butane tends to display very slight yellow tips on ignition increasing slightly as the burner warms up to full temperature) or if you use propane cylinder gas replacing the regulator if that is necessary.

If the control is working ( buttons seem to be working)

The problem is usually the igniter not reaching the correct amp draw .When the igniter does not reach the correct amp draw it may allow the gas valve to partially open or not open at all. The igniters are inexpensive and easy to replace. This video will walk you thru the correct procedure for testing an oven igniter. It may be a different model but the testing will be the same.You can also enter your model # for diagrams and illustrations of your specific model. Not all models are available. All parts come with installation instructions.

Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101

Replace the clock/digital display

check the ignitor.

If the gas doesn't come out when you turn it on then replace your glow bar. If you are getting gas when you turn the oven on then replace your oven ignitor.

i have an old model of the fridgedare gallery professional series stove. After self cleaning, the ignition sparks for the burners will not come off, they keep clicking and only stops when i pull out the plug. can you help me with this situation?

HI. This actual code cannot be cleared by pushing the Clear/off button. This actual button will usually be located on the touch pad and is a basic cancel button. You can try to reset the entire control board by simply unplugging the unit for 5 minutes. This may correct the issue. If resetting dose not correct this fault, the necessary actions are to have the defective main PCB replaced, asap.

F1 - Defective control board(PCB)

Hi,
The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating
http://www.fixya.com/support/r3663023-oven_not_working_or_oven_not_heating

Oven Problems Replacing the Igniter http://www.fixya.com/support/r4572625-oven_problems_replacing_igniter

heatman101

Hello,
Here is a tip that I wrote about the problem that you are having.

Check it out here..

http://www.fixya.com/support/r3663023-oven_not_working_or_oven_not_heating

Heatman101

Hi.


The beeping sound is a warning because the oven is in lock condition, or because a fault had been detected. In this last case there would be an error code or something unusual.


Push and hold the Clock button for about 10 seconds, that will reset the oven. If that does not work, then trip the circuit breaker for five minutes and hold the button again to reset.

If still no luck, then there may be a fault condition. In that case better calling the Frigidare number listed on the owners manual.

If the oven is two year old , then there may still be warranty cover on parts, one more reason to contact the manufacturer if the oven does not reset.

Try resetting the oven first.


Regards.

f10 error code means there is a problem with your temp probe.if you change the temp probe and this does not fix the unit then you electronic control board needs to be replaced

I need to bake in my oven how can I find the button to set the temp to bak?

Hi lack of air is the problem burner needs cleaning there is dust in the primary air ports ..

It is most likely to be the bulb which is faulty.

You should be able to replace it quite easily, nornally the bulb cover will turn anticlockwise and reveal the bulb which you then replace , remember to use a high temperature replacement.

The oven door won't open, until the oven has cooled. If you feel something is wrong with oven turn the main gas valve off for the oven, and call a repair service. If it's electric turn the circuit breaker off in the electrical panel. Don't take any chances.

Hi


Thanks for using FixYa. The air holes on the side of the burner that faces the center of the stove may be clogged or holes near the oven are clogged which are leading to uncompleted combustion of the fuel and thus leading to the foul smell. This helps the pilot or spark igniter to light the gas. Try cleaning the holes with a toothpick.

Heating elements eventually burn out. Sometimes, when an element burns out, you can see that the coil burns in too, or blisters and bubbles.

When your heating element burns out, you have to replace it because they are not repairable. If, when the heating element burns out, the infinite switch that controls it also fails, you have to replace it too.

Igniter is made up of a crystal which gets damaged or distorted physically and wont work fine until replaced. This may lead to incomplete combustion of fuel and is a safety hazard.


Please do rate the solution and revert for further assistance.


Thanks

Rylee