Frigidaire FEB27S5A Electric Single Oven - Page 4 - Answered Questions & Fixed issues
WHY WON'T MY OVEN HEAT UP?
Most modern
gas ovens and many broilers use a "glow-bar" style of igniter that
glows red-hot to ignite the gas. If the igniter doesn't reach the
proper temperature, the gas valve won't open. You may need to replace
the igniter.
11/22/2009 3:09:53 PM •
Frigidaire...
•
Answered
on Nov 22, 2009
•
10,077 views
We (Eual & Pannett Hall located in Baton
I will speak to my service manager in the morning and call you to tell you why we think you are having a problem like this.
It must be very frustrating but I hope to be able to resolve this problem for you with a simpe solution.
Frigidaire is really a great brand so I feel like it is not the brand that is causing this issue for you.
You will hear from me tomorrow. Just relax. Thanks, Ella
11/11/2009 3:41:29 AM •
Frigidaire...
•
Answered
on Nov 11, 2009
•
88 views
I have a double oven
This could be a faulty circuit or sensor that will need to be replaced before the oven safety feature will disengage. If the Temp sensor is not registering as working or the load sensor it will not allow the element to heat up. This is a safety feature. You will need a repair tech to diagnose this and do the repair.
10/17/2009 10:17:24 PM •
Frigidaire...
•
Answered
on Oct 17, 2009
•
105 views
Frigidaire FES367ASE Slide in range
Someone mis-wired the new control. Turn off the power to the range. Open the control console,switch the bake and broil wires on the oven control.
9/22/2009 9:03:17 PM •
Frigidaire...
•
Answered
on Sep 22, 2009
•
355 views
My Frigidaire electronic single wall oven
F4
Shorted oven sensor (RTD)
Check for shorted wiring between EOC and RTD. Check resistance of RTD using resistance table. If
resistance test is correct and wiring is good replace EOC
TEMPERATURE °F RESISTANCE ω
32 ± 1.9 1000 ± 4.0
75 ± 2.5 1091 ± 5.3
250 ± 4.4 1453 ± 8.9
350 ± 5.4 1654 ± 10.8
450 ± 6.9 1852 ± 13.5
550 ± 8.2 2047 ± 15.8
650 ± 13.6 2237 ± 18.5
900 ± 13.6 2697 ± 24.4
9/20/2009 4:02:20 AM •
Frigidaire...
•
Answered
on Sep 20, 2009
•
289 views
Display reads " -F3-
Replace the oven temperature sensor. Unplug the range. Open the oven. The temp sensor will be in the top right or left of the oven.A short metal piece about half the size of a pencil. Remove the screws,pull it out carefully. Disconnect the wire plug. Reverse this order to install the new sensor.
9/14/2009 11:04:55 PM •
Frigidaire...
•
Answered
on Sep 14, 2009
•
208 views
My 4 top elements work but my oven doesn't.
Take the back cover off the range. Locate the bake element terminals near the bottom of the oven. Turn bake on and check for voltage. If no voltage then replace control board. If voltage is good, then unplug oven and check for continuity. If no continuity then replace bake element. Also, does broil element work or is it dead as well? If both oven elements are dead then the control board is most likely at fault.
8/10/2009 11:42:31 PM •
Frigidaire...
•
Answered
on Aug 10, 2009
•
278 views
Error codes
hi there
ur error F-30 indicates an open probe connection....
for (F30 or F31) Check
resistance at room temperature & compare to *RTD
Sensor resistance chart. If resistance does not match the RTD chart
replace RTD Sensor Probe. Check Sensor wiring harness between EOC &
Sensor Probe connector.
if ur not confident and comfortable abt doing this work... i suggest u call a tech....
good luck and stay safe.....
have a nice day
7/16/2009 8:01:02 AM •
Frigidaire...
•
Answered
on Jul 16, 2009
•
241 views
My oven has increased only 65 degrees in almost an
The broiler element on the top of the oven comes on during the preheat cycle to speed things up and then only the lower element keeps the temperature steady. One of those elements is bad, probably the broiler. Try using the broiler and see if it works. If not, you need to disconnect the elements from the oven and check them with an ohm meter. If gthe elements check out ok, then it must be the temperature sensor/thermostat.
6/25/2009 9:15:49 PM •
Frigidaire...
•
Answered
on Jun 25, 2009
•
466 views
Dim temp. light
needs a new clock or find someone to refurb that one
6/25/2009 6:56:41 PM •
Frigidaire...
•
Answered
on Jun 25, 2009
•
308 views
Burning smells
Make sure the dryer vent hose, as well as the rest of the vent duct,
is not clogged.(this is a fire hazard)
Unless regular maintenance is performed, chances are there is a lot
of lint accumulated inside the dryer. This might affect the drying
time and could be a fire hazard. Make sure to have your dryer
cleaned regularly. Because this might involve taking most of the
dryer apart, it is recommended to have a qualified appliance
repairman perform this task.
6/18/2009 3:15:36 PM •
Frigidaire...
•
Answered
on Jun 18, 2009
•
127 views
Dont have manuel instruction i want to cleane
HI, you can retrieve your manual digitally by using the link below.just click the link provided below and, enter you complete model number. Once you enter your model number, you will be directed to the manual download page.
CLICK HERE
6/17/2009 8:43:54 PM •
Frigidaire...
•
Answered
on Jun 17, 2009
•
77 views
Not finding what you are looking for?