20 Most Recent Frigidaire FEB27S5A Electric Single Oven - Page 5 Questions & Answers

This could be a faulty circuit or sensor that will need to be replaced before the oven safety feature will disengage. If the Temp sensor is not registering as working or the load sensor it will not allow the element to heat up. This is a safety feature. You will need a repair tech to diagnose this and do the repair.

change element

Someone mis-wired the new control. Turn off the power to the range. Open the control console,switch the bake and broil wires on the oven control.

F4 Shorted oven sensor (RTD) Check for shorted wiring between EOC and RTD. Check resistance of RTD using resistance table. If resistance test is correct and wiring is good replace EOC TEMPERATURE °F RESISTANCE ω 32 ± 1.9 1000 ± 4.0 75 ± 2.5 1091 ± 5.3 250 ± 4.4 1453 ± 8.9 350 ± 5.4 1654 ± 10.8 450 ± 6.9 1852 ± 13.5 550 ± 8.2 2047 ± 15.8 650 ± 13.6 2237 ± 18.5 900 ± 13.6 2697 ± 24.4

Replace the oven temperature sensor. Unplug the range. Open the oven. The temp sensor will be in the top right or left of the oven.A short metal piece about half the size of a pencil. Remove the screws,pull it out carefully. Disconnect the wire plug. Reverse this order to install the new sensor.

Hi,

The first thing I would do is eliminate the oven sensor plug at the back of the range and hardwire it using a high temperature porcelain wire nuts. Then locate the sensor plug at the control board and measure the sensor resistance. It suppose to be about 1100 Ohms at the room temperature. Make sure there is a good connection between this plug and the control board.

Check and let me know.

Hope i helped you.


Thanks for using ' Fixya ' and have a nice day!!

Take the back cover off the range. Locate the bake element terminals near the bottom of the oven. Turn bake on and check for voltage. If no voltage then replace control board. If voltage is good, then unplug oven and check for continuity. If no continuity then replace bake element. Also, does broil element work or is it dead as well? If both oven elements are dead then the control board is most likely at fault.

need to check you drain hose is it plugged?

hi there
ur error F-30 indicates an open probe connection....
for (F30 or F31) Check resistance at room temperature & compare to *RTD Sensor resistance chart. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe connector.
if ur not confident and comfortable abt doing this work... i suggest u call a tech....
good luck and stay safe.....
have a nice day

just to clarify, if your left front burner is electric the simmer stat is faulty, if its gas I dont have an answer

f1 is a watchdog on the control board
replace control

The broiler element on the top of the oven comes on during the preheat cycle to speed things up and then only the lower element keeps the temperature steady. One of those elements is bad, probably the broiler. Try using the broiler and see if it works. If not, you need to disconnect the elements from the oven and check them with an ohm meter. If gthe elements check out ok, then it must be the temperature sensor/thermostat.

needs a new clock or find someone to refurb that one

HI, you will need to replace the EOC/clock. the power surge has fried the chip set. Replace the control board.

Make sure the dryer vent hose, as well as the rest of the vent duct, is not clogged.(this is a fire hazard)

Unless regular maintenance is performed, chances are there is a lot of lint accumulated inside the dryer. This might affect the drying time and could be a fire hazard. Make sure to have your dryer cleaned regularly. Because this might involve taking most of the dryer apart, it is recommended to have a qualified appliance repairman perform this task.

HI, you can retrieve your manual digitally by using the link below.just click the link provided below and, enter you complete model number. Once you enter your model number, you will be directed to the manual download page.


CLICK HERE

eplace the oven temperature sensor.

bake broil selector need to be replace