Krups Small Appliances Espresso Machine - Page 2 - Answered Questions & Fixed issues
Leaking xp7240 clean valve
Which valve where exactly, in the pump, in the tamping piston, in the distributor or somewhere else?
7/23/2014 6:30:15 AM •
Krups Small...
•
Answered
on Jul 23, 2014
•
312 views
Code 12 krups
There was no ejection switch pulse during 2x empty cycles. Inspect the switch or what activates the switch, check the wiring to the switch and PCB. Is the chamber clogged with grinds.
6/11/2014 5:53:02 AM •
Krups Small...
•
Answered
on Jun 11, 2014
•
1,088 views
Krups 8025
Yes the distributor is the most likely cause, if you have done the O rings in the hydraulic ram assy you should be capable of changing the distributor. The only other thing I have seen dump water to the tray is the valve on the end of the pump with the hose going back to the tray. You can pull the hose off at the tray end and run the machine to determine if that's where it's coming from. It won't be easy. I have an outer housing with lots of cutouts so I can observe inside while it's running.
4/30/2014 10:32:59 AM •
Krups Small...
•
Answered
on Apr 30, 2014
•
142 views
Why wont krups light wont go off
This solution assumes you are trying to turn it off and it won't.
If it is a model like in the photo it could be as simple as a switch button, does it seem a bit looser than normal? If it's not that you may need to change the pcb on the left hand side.
If this solution does not help give some thought to supplying a model number and spend a bit more effort describing the fault.
4/27/2014 9:06:20 AM •
Krups Small...
•
Answered
on Apr 27, 2014
•
47 views
Switch problem
Hi Porl, my answer was assuming that your machine is the product in the picture, if your machine looks nothing like the picture then ignore my answer. It is not easy to answer questions when no specific model information is supplied.
3/4/2014 6:59:48 PM •
Krups Small...
•
Answered
on Mar 04, 2014
•
45 views
XP7240 not draining properly
Replace that pressure valve and also inspect it for leaks from directly under the boiler, from that pressure valve and from the top of the hydraulic ram. If when you buy your valve you find the white housing will not fit where the old one came from you can just use the piston into your old housing. Check this before removing the hose clip from your old piston housing. If your old piston housing is leaking badly before you even do this job then you will need to replace the whole distributor as sometimes a piston housing retaining lug can fracture, there are 3 of them and they are part of the distributor.
3/1/2014 9:15:32 PM •
Krups Small...
•
Answered
on Mar 01, 2014
•
395 views
Its about my Krups 8220. It gets stuck after it
Take it in to your Krups service agent, something is going to need replacing and they are by no means a simple machine to work on. You will fix nothing from the outside, it will need to be pulled apart.
10/18/2013 7:30:52 AM •
Krups Small...
•
Answered
on Oct 18, 2013
•
1,583 views
Keep asking me fill up the water tank even it is
Inside the water tank there is a magnetic float which is causing the problem. This float is moving always on the top of the water tank as you fill it with water and in reverse as the water level goes down then the float is moving down to bottom also. So as the magnetic float is moving up and down is giving the signal for the water level if it is full or empty.
So possibly now the float is stuck in the bottom and even if you have refill the tank this is still on the bottom of the tank. This can happen from many reasons. First could be that the plastic column that the float is moving is full of scale and it can not move up and down freely any more so you can clean it from scale by decaling it and even clean it with a wire brush.
A second possibility could be that float have a tiny hole and some water enter in the float and this make it to stay on the bottom of the tank. You can visually inspect it and if possible you can dry out the water and weld with a super glue the hole if possible, if it can not be fixed then you need a new float.
If you wand to fix it temporary until you find a new float you can a plastic clip or similar to secure it always on the top however you when the tank is empty it doesn't register so you would really have to keep an eye on the water level to avoid any other problems with the machine.
Good luck
8/14/2015 1:03:09 PM •
Krups Small...
•
Answered
on Aug 14, 2015
•
707 views
Krups error 7
for error 7 is the jam milling or cylinder obstacle .,good luck to youJoseph
8/31/2012 4:30:26 PM •
Krups Small...
•
Answered
on Aug 31, 2012
•
734 views
Lots of disturbing noises, no coffee
It is is easy, if you know how to do it... as always
First take of the wather, trach bin etc,
Start with removing the cup wher the beans is stored, the adjustment knob for the mill is a tricky part. Remove it by bending out the side of the knob. Thereafter remove the screws from cup and those you on see on the top.
The front (silver frame) is removed by lifting it upwards, behind it you have 4 screws that has to be removed.
The last two screws is found under the wather tank.
Now you should had take away 11 screws, at least...
Bend the back of top and it will be off. Finally push the rest of the plastic cover backwards.
Do you know what the error codes says? I have know 6,8and no coffy...
7/1/2011 3:51:54 PM •
Krups Small...
•
Answered
on Jul 01, 2011
•
1,006 views
I have a Coffee Machine
I have not found a solution yet but i am appalled that a company like Kuerig expects its consumers who are all experiencing the same problems with their machine to pay for online tech support.
I loved my kuerig and considered purchasing another one if i could not find a solution to my problem but i am so turned off by this that i will not purchase anything from this brand in the future. I bought both of my children and my mom one of the macines but at this point i'm done with the brand!
6/22/2011 1:22:49 AM •
Krups Small...
•
Answered
on Jun 22, 2011
•
335 views
Not finding what you are looking for?