20 Most Recent Jenn-Air JGR8850 Gas Kitchen Range - Page 4 Questions & Answers

Hi ,you will need to replace control panel part # w10206073 cost about $175 and is currently on national back order,try making sure the ribbon connector between the panel and board is tight and clean.Hope this helps. Please rate my response :)

Hello there:
Here is the 2 most common f1 codes for this oven and what the problem is and what repair procedures that should be taken
F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad) F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC)

Yes, we have the grill covers for your Jenn-Air range. Just contact us at:

http://www.fixya.com/repair/d499389-accurate_appliance_repair_service from 7 AM until 7 PM CST Monday through Saturday and we will get this out to you asap.
We look forward to working with you.
Thanks, Ella

you mean the convection fan don't you, the one inside the oven.if it's coming on by it'self you need a new control/clock you will need the complete model # to make sure you are getting the right one about $200.00 retail price

the oven gets to near 1,000 deg inside it takes a wile to cool don't try to open it for at least an hour if your worried it's stuck turn the power to it off, the door will not be able to be opened till it's cool and the power is turned back on. go to jennair web site download use and care manual

There is a controler which if you trace your gasline from the oven line to where it juntions into the controler could be bad or the thermo coupler went bad

Hi. This is the result of circuit damage, within the touch pad board. Most units will have the touch pad, and main control board totally integrated(one whole piece). There are a few Jenn-Air(aka whirlpool) models, that may have the touch board separate from the main control board, connected via ribbon cable. if this is the case, simply replace the touch pad board.

NOTE_ Damage of this nature is not repairable. the entire circuit board must be replaced.

http://www.appliancepartspros.com/modelnumber_locator.aspx
Try this link for help with model number. Post your number in a appliance parts site to find the part.
http://www.searspartsdirect.com/partsdirect/index.action?psid=26129238&sid=PSx20071217x00001a
http://www.appliancepartspros.com/partsearch/
http://appliancejunk.com/forums/

took off the knob to the ignition system to clean and spray got onto the ignition under the dial and now the two front burners won't ignite unless I turn on one of the functional back burners then turn on the front burner. How do I repair this?

This means the controller has detected a problem related to the temperature sensor. It could be the sensor itself, pinched/shorted wires or connector to the sensor not seated properly.

Sometimes this is due to a failure in the controller itself. If this turns out to be the case, we may be able to help you. We repair oven control boards.

Regards,
Bruce
www.fixyourboard.com

the best otion for you is to install some sort of damper weather automatic
or hand operated

you have a bad ignitor on the bake side
take out the racks
take out the bottom pan
you should see the ignitor
tun on the range and watch the ignitor
if its only orange and notr glowing white
it wont open your gas vaslve
asnd need to be replaced

this is a water gasket
you can repair it pretty easy just find a rubber band that will fit

This is an occasional problem for many brands. 1st, it depends whether you have a lever in front that locks the oven door or the door is locked electronically. If you have the lever, it is common for the lever to get bent too much to the right or left so that it does not (after while) come back to the full open position, yet it looks like it is fully in the open position. You will have to bend the outer part of the handle in order for it to travel the extra distance to fully release. Or you will need to lift the top (be careful if it is sealed burners;some sealed burners need to be removed before the top can be lifted or you will damage the burner tubes or the ignitor wires). You will then see a plate to the front of the range where the lock mechanism is located. Under this plate you will find the lock engsging pin or finger and posibly an electric selenoid coil ( basically a magnet coil that energizes the lock pin/finger). You must release this from the latch arm or latch hole on the oven door. This will get the door released and now you need to determine if the selenoid or the mechanism was at fault. There also may be a small switch that is turned on/off that is attached to the mechanism and this is the safety fail switch that sends the signal to the oven control to operate or not operate in clean mode. This switch could be stuck or internally fused in the on position. Hope you have the tenacity and skill to determine all this. Good Luck, Macgivor

F9 is a door latch error. You have to check the door latching system for functionality

what does f9 mean and how do I fix it?

Replace lower igniter.

Door latch problem. Check door latch... If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Anytime you turn on a gas range all burners click for safety reasons. If a knob has been turned by mistake the gas lights to prevent gas from escaping into the room. If you turn the control knob past the LITE position after the burner lights you should be OK and stop the clicking. If the clicking continues regardless you have a defective ignitor switch that must be replaced.