Jenn-Air JDR8895AAS Dual Fuel (Electric and Gas) Kitchen Range - Answered Questions & Fixed issues
Burner Problem
it appears that the air intake intake is incorrectly set or you have the incorrect gas jets fitted to the product.
Regards
Engineer
1/3/2017 4:46:52 PM •
Jenn-Air...
•
Answered
on Jan 03, 2017
•
398 views
Jen air locked latch after cleaning
I finally got my oven to work properly by shutting off the breaker and resetting the main clock. Cured the always locked problem as well as the beep twice when self cleaning.
Have to repeat this every few months since the problem seems to come back.
4/22/2015 8:37:33 PM •
Jenn-Air...
•
Answered
on Apr 22, 2015
•
694 views
The lower oven heats up really slow and stops at
The problem may be caused by different components but most common is the oven temperature probe. It could also the the thermostat. A technician can measure the resistance of the probe at a known temperature and determine if it is failed or not.
10/31/2013 2:55:11 PM •
Jenn-Air...
•
Answered
on Oct 31, 2013
•
130 views
Where is the fuel pump fuse located 1999 gmc jimmy
Underhood fuse block- "ECM B" 20 amp fuse. It supplies voltage to the fuel pump relay in the same fuse block, which sends voltage down the line to the fuel pump when the engine computer turns the relay on.
10/19/2013 7:39:39 AM •
Jenn-Air...
•
Answered
on Oct 19, 2013
•
259 views
Turns on by self
from what i can find there can be a fault on the mother board but it does not say what.if yours is the tutch model it could be to sensitive also if there is a grease build up it could be shorting a circuit.
9/22/2013 4:13:37 PM •
Jenn-Air...
•
Answered
on Sep 22, 2013
•
54 views
Line diagram oven
Pull the temperature probe and with a multimeter, check the Ohms. It should read right around 1100 Ohms at room temperature. If you get any other reading replace the probe.
Here is that part to order.
5/3/2013 8:09:01 PM •
Jenn-Air...
•
Answered
on May 03, 2013
•
77 views
Jenn-Air JDR8895AAS error 1c1c
1C1C Shorted Key - Check wire harness connector and ensure proper connection and wires show continuity to the control board. If ok, replace the control board. Here is the part to order.All parts come with a 365 day, any part, any reason return policy.
2/6/2013 1:17:28 AM •
Jenn-Air...
•
Answered
on Feb 06, 2013
•
659 views
Beeps and flashes FC
The "FC" error code means "Communication error between boards".Check the "J2" harness, ohm wires end to end. If the harness is fine then the display board is defective.Here is the part to order.
1/24/2013 10:54:39 PM •
Jenn-Air...
•
Answered
on Jan 24, 2013
•
327 views
Jenn-air
What is the complete model number of your unit?
12/5/2012 10:26:13 PM •
Jenn-Air...
•
Answered
on Dec 05, 2012
•
347 views
Uneven Temp in Ovens after Self Cleaning
in the users manual there will be a calibrating page. also self clean is hard on the oven a sensor that is meant to read 400 degrees has a hard time being accurate after 900 degrees
11/14/2012 7:22:24 PM •
Jenn-Air...
•
Answered
on Nov 14, 2012
•
344 views
Not finding what you are looking for?