Jenn-Air JJW8530C Expressions Collection Dual Single Oven - Page 2 - Answered Questions & Fixed issues

Hi, the error code implies that the Function key shorted or stuck..
You need to replace touch pad or if touch pad is part of the clock, replace the clock (ERC).

hi the only to fix it is to replace display/control jim

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101


hgddg

sounds like a bad keypad

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

This problem is likely a failure of the LCD display on the circuit board. I examined ours and it shows a burned spot inside the display unit. With our oven the display becomes visible after the oven has been on for some time. The board is simple to replace.

probably a bad oven control board. check the lock switches too while you in there messing around getting lit up lol

I have the same problem. Just swap the 2 wires that are marked as 'broil' and 'bake' on the controller board. But sometimes it switches back, then I have to swap the wires again.

You might want to leave the 'broil' post unconnected to prevent burning food..

replace the oven sensor . if this does not correct . look at the ELECTRONIC OVEN CONTROL. THE SENSOR TELLS THE CLOCK THE TEMPT AND THE EOC CONTROLS OVEN TEMPT . . now don't forget to ck the element first and the 220 power . .. if i/2 of the power is missiing due to a triped fuse the low tempt or not temp is possible.. mm

Check out www.appliancetimers.com They can rebuild your clock for around $100. A new Jenn-Air is like 2 grand.

Hi,
Before you go working too hard to get you oven to go into the self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem
http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!!

Hello- The code described F1/ F7 indicates a 'stuck' key on the control panel. The problem is fairly common, and is not caused by computer. The panel is actually more expensive than the computer. On site diagnosis is needed to confirm. The switch is on a circuit board behind the panel and is not serviceable. Find a good service tech in your area to check it out. Wish I had good news, but I installed several of these under 1 year warranty period.  So- let me know if this info helps- have more if needed.   Thanks- Ed

If there is no slot for a screwdriver or cross point screwdriver, then, yes, it will be secured from the outside of the oven.
It will mean removing the rear panel, and possibly the top as well.
Hope this helps.

Actually I did not solve the problem as I'm just looking for a manual for the wall oven so I can set the clean cycle. I just can't see joining a service for just one manual.

Thanks,
Sigmawolf

Check for a tripped breaker or blown fuse in your fuse box. Assuming they are separate units there is no common connection other then the power source.
Good Luck,
Gilshultz

You have a defective spark module. This is a device which breaks down the 120 incoming volts to a 12 volt spark to ignite the burners. Replace module and problem should be solved.

No or dim display? You can replace the clock at about $160.00, or Check for a burned capacitor on the clock board, The likely culprit is labeled C3 on the board, its a 35 Volt 68 mF capacitor that needs to be replaced with a high temp (105 degree C) capacitor . Any capacitor that shows signs of discoloration and or leakage should be replaced with the same value but high temp. component. You can use regular capacitors of near equal values in a pinch but find the good ones of the correct values for a long term fix.

Here's a link to the Jenn-Air web site with a free owners manual that you can download.. They have two different ones listed, so rather than post a direct link to the manual, I post the link that will allow you to select the correct one for your oven.

You need a couple more letters added onto the end of your model number (either a AW or CW) to determine the correct manual for your oven.

http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=JJW8530C&siteCd=JA_EN_US

Hope you found this very helpful and best regards!

this is what you most likely need. Age, or the clean cycle, can cause them to start to malfunction.

http://www.repairclinic.com/SSPartDetail.aspx?s=t-W131B-%3d%3di1364&PartID=1364

It is inside the oven, and comes out/goes in pretty easily, but you have to be careful when removing the old one, not to loose the wires in the hole, because then you have to pull the unit out from the wall and remove the back in order to plug the new one in.

When you turn the burner dial, all igniters spark. Most brands work this way. The dial activates all igniters to spark but only opens the gas valve attached to that dial.

Do you mean that they continue to spark even when you are not trying to light the stove?