Jenn-Air JJW8530C Expressions Collection Dual Single Oven - Answered Questions & Fixed issues

its just not that often the probe fails without setting a code

I think that is a problem with the control assembly.

Try first unplugging power cord for ten minutes , and see if this clears the error message.

check tthermostat

I replaced the C3 capacitor on the circuit board and works fine. This was mentioned in a prior post and took 5 minutes and was under $5.00 for the part.

If you haven't already, replace the capacitors on the clock module. I had the same problem with a similar oven. See this link for more info:

http://www.badcaps.net/forum/showthread.php?t=7902

When an oven doesn't maintain the set temperature, first make sure no one is allowing the heat to escape by opening its door. If not, the oven control either needs to be re-calibrated or replaced. To have the control replaced, call an appliance service person.

For basic cleaning, use a non-abrasive cleanser or detergent and water. Clean the oven frame, oven door outside of the gasket and the gap in the gasket. (Don't clean the gasket.) With a damp sponge (with detergent if needed), wipe up any spills in the oven. (Sugary or acidic spillovers could damage the porcelain.) Wipe up any grease that spilled in the oven. Wipe the control panel with a damp cloth then dry. Clean the oven door with detergent and water. Clean the window or glass with detergent and water or glass cleaner. Use care to keep the water from seeping behind the window.

Next if you want to do a self-cleaning cycle. Remove the oven racks, the broiler pan and any other pans or items that are in the oven. Close the oven door. Press the Clean pad and then press Autoset(0) button to get the length of time to run the cleaning cycle. Press 2 or 4 to shorten or lengthen the cleaning cycle. After 5 seconds the door will lock and the cleaning cycle will begin. The door will remain locked until after the oven cools down (at least an hour after the cycle ends). Wipe up any white ash after the oven door unlocks. If you want the cleaning cycle to be delayed, press the Stop pad within 5 seconds of setting the length of the cleaning cycle. Use the number pads to set the time that you want the oven to end the cleaning cycle. (Make sure that it is later in the day with sufficient time to run the cleaning cycle.)

Most Jenn-Air manuals are available here: http://shared.whirlpoolcorp.com/product_literature/search.jsp?siteCd=JA_EN_US . The direct link to the manual for the JJW8530CAA is http://www.kitchenaid.ca/assets/pdfs/literature/JJW8527AAB.pdf .

I hope this helps.

Cindy Wells

Hello,

The F9-3 error code means that their is a problem self clean door lock system. Typically their is 2 switches that check the position of the door latch and even if it's open and not in self clean mode the switches are telling the computer the latch is closed. You should if fairly mechanically inclined be albe to find the latch behind the control panel and use the wiring diagram there and check those switches using a meter set to a low ohms setting and check for one switch being open (infinate ohms resistiance) and the other to be closed (zero ohms)

Good luck, i hope this helps

Gene

Hi

F7 error in your Jenn Air means stuck/shorted key, to solve this issue the buttons/keys should unstuck as you have already replace the clock assembly. After checking all the buttons if the issue returns then the touch pad/key pad assembly should be replaced. Hope this helps...please post back for further assistance.

Daniel

Yes, its problem with touch-pad/control-panel board assembly problem.-------- it has to be replaced, and this will correct the problem.---- This is the part number for the part.-------- 5765M306-60 --------- To order this part you can order it from sears site or from repairclinic or from partsselect.------ But this part is available at part-select only at present.On other online site this part is current out of stock.----- But will be available soon.----- Now click both this links one by one:--- This is repair clinic link on this site you can see the picture of the board which you require:--- http://www.repairclinic.com/PartDetail/Touchpad-and-Control-Panel/5765M306-60/1488665 ------------- but at repair clinic it says part is currently out of stock.-------- now click this another link, on this site this part is available:--- http://www.partselect.com/PS2357899-Whirlpool-5765M306-60-Control-Panel-with-Touchpad-Black.htm?SourceCode=3&SearchTerm=5765M306-60&view=b ----------- Also click sears link, on this site the part which you require is most cheap, of all other sites:--- http://www.searspartsdirect.com/partsdirect/part-number/5765M306-60/0022/664?pathTaken=partSearch&filterPart=&pop=flush&prst=0&shdPart=5765M306-60 ----------- This will help.Thanks.Helpmech.

Hi jmhostetler9,

This F3 that keeps flashing on your oven is caused by a shorted or open oven temperature sensor (RTD). To fix this problem check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.You may contact Sears for the replacement part at 1-800-252-1698; M-F 6:30 AM-10:30 PM - Sat 7:00 AM-9:30 PM - Sun 7:30 AM-9:30 PM - All times Central. Just get your model # ready when you call.

Hope this helps.

Thank you for using FixYa.

That noise just lets you know that the unit is on/in operation.

just finished cleaning and FC comes on and wont stay off. constant beeping

I have Jenn Air oven S136-C with a locking bar. After cleaning cycle wait for the oven to cool down and the lock light will go out (but the oven is not yet unlocked.)

Set SELECTOR knob to OFF
Set TEMPERATURE knob to CLEAN
Press CANCEL button (on right) twice.
Slide the locking bar to the left and the oven door will open

One side of your 240 volt connection is disconnected, most likely in the plug wire connection. The neutral and one leg of your 240 is working thereby your display still works since it runs of 120 volts. Happened to me I had one wire come loose from stress on the plug

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking

heatman101

F1 touch pad / ERC test This simple test will help determine
whether the ERC (Electronic Range Control or Clock) or the touch pad is
defective when F1 error code is present.



Note: Some models incorporate the touch pad in to the ERC as a single
assembly, in which case this test is not necessary. Simply replace the ERC
(Clock).



Warning: If you feel in any way uncomfortable performing this test or
making this repair, please contact a qualified appliance repair technician.


1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing


2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC


4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was


5. Turn the power back on.

6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound)


7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hi,

Before you go working too hard to get you oven to go into the self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem


heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!!

Yes, the problem you are describing is most likely a fried heating element. This can be repaired for around $40

Hi,
If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101