Konica Minolta bizhub C450P Laser Printer - Answered Questions & Fixed issues

Background Explain!!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Fax board error did you replace it or remove it?? was it installed ? did you install correctly there is a procedure

Abnormally high toner density detected black TCR sensor TC ratio in the imaging unit, which is determined by toner replenishing amount control mechanism, is a predetermined value or more for a given number of times consecutively. check for developer check TCR sensor check toner sensor check the PRCB

power error code

Abnormally low toner density detected Black TCR Sensor.

Am having little Challenge if I send job to printer Bizhub c451. D job will enter printer and it will wrote System Printing and it will not print

Problems bizhub c452 print dust

Pls to slow help me

DID you swap a board from a different machine if so you really messed up the machine, Have a tech come out to look it over mite run below? NVRAM holds the serial number and counts so people cant erase the counts as new. CD3##: NVRAM Data error • When the data stored due to the NVRAM trouble is lost, backup data can be used for restoration. • Trouble code [C-D370] will be displayed when multiple errors (over 5) of NVRAM data are detected, which can be restored with one restoration command. • Data backup will be automatically performed every hour. Backup can also be performed manually with the following setting. [Service Mode] ? [Enhanced Security] ? [NVRAM Data Back Up] Touch the following code on the trouble code display screen. Stop ? 0 ? 7 ? 1 ? 3 ? 9 2. [*] will be displayed on the trouble code screen. 3. Touch [*]. 4. The screen will be shifted to the data restoration screen to perform data restoration. NOTE • When the restoration is performed in a short time, data restoration screen may not be displayed. 5. Check the message which indicates that the data restoration was successfully conducted. Turn Main power OFF, and wait for ten seconds or more to turn it back ON. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sir/Mam, Turn off the main power switch, ensure the sub power switch is on. The sub power switch is located on the right side of the control panel. Then holding down the Utility/Counter button turn the main power switch on. Close the front door you must keep the Utility button down. The screen will show TROUBLE RESET touch it sees a "OK" then power off the machine. YOU MUST WAIT TEN SECONDS BEFORE POWERING UP AGAIN!!!!!! If the problem goes away OK. If the code comes back, you need a Fusing unit Which will be expensive!!! Sorry :( DO NOT KEEP TRYING TO RESET THE MACHINE! THE MACHINE IS TELLING YOU THERE IS A PROBLEM!!!!! A Fire could occur and that would ruin a perfectly good day!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the fuser and reset the machine Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

C450 P or c450 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Well you need to log in as administrator reset the IP address the mask and gateway. it is still on the old net work and was set as static IP address which mean it not set up for DHPC Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try removing the default settings.

Behind the machine very bottom where # 3 draw is there is a small hole. Unplug the machine stick a screw driver in there to manually release draw number 3. the Code is dealing with the life section of draw number 3 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Yellow Imaging Unit Failure. Take out IU-Y, shake it, check the toner layer, Re install it. and see if improvement, else remove IU-Yellow

If you wish to get some details; check the site linked here. Pull up older posts...... http://electro-medical.blogspot.com/

how thick is thick maybe to thick for the printer check the the specs Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

does this happen with word , pdf, web pages, email? what other indication display on screen Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

missing digit on code c-xxxx Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f