20 Most Recent Asrock 775i65G Motherboard - Page 8 Questions & Answers

double posted you?of 29mobo not one told.https://www.asrock.com/support/index.asp?Model=h110the bios page,labeled, igpu (disable /enable ) is there.some mobo allow zeon here with zero igpu.but not yoursthey make h110 ,mobo just for useless now, bitcoin mining.watch the netflix movie how the blocked mining,then save moneyalso learn what ROI is?

Check Ram and fun if not properly installed

First of all, check if there are any inflated capacitors, if there is even one- ditch MBO, other capacitors will soon follow. If no inflated capacitors proceed with these diagnostic steps: 1/ disconnect all peripherials (DVD, HDD, card reader...), leave only MBO, PSU and RAM (and CPU of course); if nothing happens 2/remove CMOS battery (CR2032) for 20-30 sec with power cord disconected from computer, that will reset BIOS; 3/ take out RAM sticks, then, if you have more than one stick, try with each stick separately (it might be faulty RAM); 4/power on MBO without any RAM-if speaker is present it should give BEEP signals; 5/ try with different PSU, many power supplies are faulty even when they do give power to MBO. If nothing of above does not help than you have faulty MBO, because CPUs are so rare to fail that in my 10 years of experience in PC service I had 3-4 fried CPU-s, and even that was because costumer tried to clean PC, removed CPU cooler and than incorrectly placed it back or didn't put thermal paste afterwards.

3 post all the same mobo and all 3 same reasons. and all 3 same answers. zero no I added one, coin cell is dead at 7 years, you are 2004 to 2018 late to the party. 14 year old battery is 2 times spec life. for sure.

http://drivers.downloadatoz.com/download/76103,compaq-nc4200-intel-vga-driver.html maybe.

Wipe the hard drive and do a clean install, not repair.

swapping out parts, try with different power supply pull the ram reseat it maybe one at time. different memory slots. change one part at a time with good working part, never assume any part is good.

That would be ******* and we don't so that here. Sorry.

Si ustedes quieren activar Windows 8 necesita una clave de producto, te tengo este enlace para obtener algunos m?s estables: https://plus.google.com/117868268119072465334/posts/XuMyoTaUjN7.

Hace unos d?as, me dieron una de las ventanas 7 clave de una p?gina: http://www.instructables.com/id/C%C3%B3mo-Reparar-Error-0xC004F074-De-Microsoft-Word/. Despu?s yo uso la tecla. Clave no s?lo funciona sino que es genuino. La esperanza tambi?n puede ayudar.

Almost any muffin fan that will fit should be ok. Make sure your motherboard can run 64bit before you spend your money!

http://www.asrock.com/mb/Intel/ConRoe945G-DVI/ find this to help.

Perhaps the install is trying to open a file with an mc2 file extension. Has this prompt at startup just started happening or has it always been happening? If it has just started did you recently download something? MC2 files are Misc Files primarily associated with Mastercook File (Sierra). There could be other programs which also use files with this file extension. It sounds like your system is trying to open a file with an mc2 file extension and does not have the proper program installed to do so. It is asking you whether you will allow it to install the file for you.

does your mac have a battery back up battery like pc's do. the battery in the mac may not have enough power to keep the cmos information together, replace the battery and you should be okay

i have your problem.but when i use asrock mac tool it said "Not supported"!.infact it not supported mac address on stick on main board!but my hope was the mac 6 digit that newer tool write.then i change my mac by mac changer from windows and then set that mac to bois and flash by asrock mac tool.every thing get ok:)

first remove cotter pin from retaining nut then keep axle from turning by installing phillips screw driver in outside axle hole on opposite side loosen retaining nut now each side of axle has adjusters loosen nuts on adjusters turn adjusters clockwise to tighten chain and counter to loosen chain after adjustments been made tighten nuts on adjuster and retighten axle nut and reinstall or replace cotter pin

Bad Ram