Top 20 Whirlpool GGQ8831L Gas Dryer Questions & Answers

this has gas coils on top of the gas valve the flame might ignite for the first 10 to 15 minutes but if the coils are failing you won't have any flame after they heat up,when they cool down they will work again so i would say you have bad gas coils,easy fix,remove the two phillips screws,remove the top cover,remove the connectors off of the coils and reinstall the new coils,watch out for the large coil,there's a spacer that slides onto the post,if it's not there poke it out of the old coil and slide it back on the post and then slide the large coil onto the post,i've gone in and found this missing on some dryers that the customer had changed out the coils themselves before,it will still work but it can chatter alot.also while your in there remove the thermal fuse and the cycling t-stat both on the blower wheel housing and make sure there's no lint buildup on the back of them,if so just clean them off and you'll be fine

Also check the vent. It is trying to tell you there is no air flow.

Most of the igniters are located in the lower front area of the dryer. You need to remove the top cover from the front area , using a spatula to Pop it open (don't forget to remove the filter if its located on the top, Including the two screws that hold the base) . Then you need to remove the front plate by removing two screws from the inside upper Area . The igniter is a ceramic fuse that will click and glow completely Red and ready for the gas to create the flame and heat for you dryer. If you model has a bottom front cover only and after you remove it ,then it will be easier to observe The actual process of the igniter if it is working properly . Good luck

There are several thermal safety fuses in dryers which once blown have to be replaced. But, more importantly, they normally blow for a reason and simply replacing one without resolving the underlying problem of overheating will simply cause another failure. Lint is the normal culprit; vacuum and forced air to clean everything out. WITH THE POWER CORD UNPLUGGED and the leads temporarily disconnected, check continuity on each of the thermal fuses (they look like a stainless steel hat that might fit on a Barbie doll. Some dryers have four or five.).

Take a look at this video. It will walk you thru the troubleshooting process.

Hi,

Yes and no....

Do not place the kit immediately off of the dryer...give it at least a few feet of space from the dryer to the kit to let it cool down a bit before getting to the kit.
Make sure to check it often and keep the hose and the kit clean....if it clogs up it will cause things inside the dryer to go bad...

Take a bit of care and install it properly, keep it clean and you will be happy with it.

heatman101

Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check outthis electric no heat tip...

heatman101=-
=-
-=

this website will help, more then likely you will need to clean the venting system and replace all the recommended parts for your dryer:

http://www.applianceaid.com/gas_dryer.html#noheat

Hello & Welcome to FixYa

The loud noise that you hear is from the belt that is either broken or worn out, you can check this picture....part#30 is the belt that needs replacement. Also check the idler pulley (part#13) and motor pulley (part#29). Please get back to me if you have any other questions.

Kevin

Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

if you dryer is gas check out this gas no heat tip....

If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.

check out this electric no heat tip...

heatman101

-;-;-;-;-;-;-;-;-;-;-;-;-;-;-;-;-

Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

if you dryer is gas check out this gas no heat tip....

If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.

check out this electric no heat tip...

heatman101
,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.,.

The problem is the dryer coils have failed. They tend to fail as they heat up. They are inexpensive and easy to replace. Here is a link that should help troubleshooting a gas dryer

Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check out this electric no heat tip...

heatman101

Normal 0 MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Hi,
If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

if you dryer is gas check out this gas no heat tip....

If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.

check out this electric no heat tip...


heatman101

Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check out this electric no heat tip...

heatman101

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor going bad...

Here are a couple of tips that I wrote will help you to figure out why your dryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

As you may know the gas continually comes on and off all through the cycle to regulate the heat. So the ig nitor and flame sensor is working because you hear it. But the lack of heat is due to faulty solenoid coils getting hot and quitting. When they cool off they work just a little bit more. Very hard to diagnose but easy to fix. Just get some new coilsDrop the bottom panel and you can access the gas assembly If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Hi,
If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

Check out this tip that will give more details…

Gas dryer not working gas dryer not heating
http://www.fixya.com/support/r4398592-gas_dryer_not_working_gas_dryer_not


If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.
Check out this tip to see the things that can fail to cause your electric dryer not to work.

Dryer Troubleshooting Electric dryer wont heat
http://www.fixya.com/support/r3866345-dryer_troubleshooting_electric_dryer_won


heatman101

Your service manual, or wiring diagram for this machine should be located in the control panel housing.
Most likely you have a blown thermal fuse. This part is located on your blower housing right behind the lint screen duct. The power for your gas valve/burner assembly is routed through this part and will be cut off should the drum temperature get too high during operation. The part is a skinny white colored item with a black strip down the center, a quick check would be to see if it has continuity, or simply bypass it briefly to check it. DO NOT leave the part bypassed.
To access the part remove your lower front access panel, remove the lint screen for m the dryer and then remove the two quarter inch screws on either side of the lint filter housing to remove the housing.
The part number is a 3392519 thermal fuse.
Good luck to you on this.

May need to check gas pressure to unit...