20 Most Recent Whirlpool LSR6232J Top Load Washer - Page 9 Questions & Answers


Sorry we do not have that kind of info here, contact Whirlpool.

Whirlpool... | Answered on May 31, 2019


Problem with the Whirlpool Shift Actuator. Fault is displayed when the main control cannot determine position of shifter. • Check harness connections from main control to motor and shifter. • Observe shifter operation. Replace the shifter if it is bad.

Whirlpool... | Answered on May 30, 2019


https://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-cabrio-top-load-washer-error-codes.html
Motor Stalled The motor RPS (Rotor Position Sensor) detects no rotation of the drive motor. Unplug the washer. Check to see if the basket spins freely. If not, then examine the drive system and eliminate the cause of friction. If the basket spins freely, check the wire harness connections between the main electronic control board and the motor. If the wire harness connections are okay, check the drive motor. If the motor is defective, replace it.

Whirlpool... | Answered on May 27, 2019


You have to access this dryer through the front. First, unplug the dryer. Next, remove the lower front panel. There are 2 hidden metal spring clips in the seam above the lower front panel and if you slide a flat head screwdriver above these clips you can pry them down and the lower front panel will hinge forward ad down and unclip from the top. Now the fuse is mounted to the top of the blower wheel housing behind the lint filter enclosure. But the fuse stops the motor so that isn't going to be the problem.If the unit is just not heating, look at the heating canister under the drum along the right side. There are 2 small devices attached to the left side of the heating element. Test these 2 parts for continuity and if either are open, replace it. Also test the heating element itself for continuity and if that doesn't have continuity, replace the element.
https://www.justanswer.com/appliance/a78fy-locate-fuses-whirlpool-ultimate-care-ii.html

Whirlpool... | Answered on May 25, 2019


Sounds like the belt under the machine is either broken or off the motor/pulleys. Empty the tub, turn off water, disconnect the power. Pull unit away from wall, tip it back so you can look underneath (Make sure to put blocks under machine so it doesn't fall on your head)Find the old belt to get the size. To replace the belt, put it on the motor pulley, the on the large pulley, then the small one. The motor mount is usually under spring tension.

Whirlpool... | Answered on May 25, 2019


The panel of some top loaders is fastened by screws which are removed to allow it to swing upward for access.

Whirlpool... | Answered on May 22, 2019


Possible cycle timer failure

Whirlpool... | Answered on May 21, 2019


LD = long drain. possible pump issue or obstructed drain hose

Whirlpool... | Answered on May 20, 2019


PROBLEM RESOLVED!!!

The best I could find by scouring the internet was that it was a communication problem between the central control unit and the electronic control box. I was getting F1 codes that would stop the wash, then diagnostics showed F68 and F41 codes.
Sears wanted to charge $65 just to come out and diagnose it themselves, and these appliance sites wanted to charge their own fees to offer solutions. So I took a chance and ordered a new electronic control box ($146.00 + S&H) and installed it myself.
There are three long screws behind the control unit "hood", in the back-top of the washer, facing straight up and down. After unscrewing, I lifted up the hood up and forward, and there was a black box - the electronic control. First, you should check all the wires and make sure the connections are ok. If that still doesn't fix it, unplug all the wires, and take the electronic control out by unscrewing one 1/4" bolt. Put the new one in and re-wire everything (it shows what wires go where on the electronic control box - named by colors). No more error codes!

This washer is only a year and a half old as well, I guess it will pobably be my last Kenmore/Whirlp

Whirlpool... | Answered on May 18, 2019


contact whirlpool. this website is usa based and we dont know

Whirlpool... | Answered on May 18, 2019


check your spinner is working or not check the spinner button first and try to fix by opening back cover of your machine

Whirlpool... | Answered on May 17, 2019

Not finding what you are looking for?
Whirlpool LSR6232J Top Load Washer Logo

Popular Tags

39 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Washing Machines

  • Whirlpool Washing Machines

Most Popular Question

lid switch fell out whirlpool top loader

  • Washing Machines
Loading...