Top 20
Whirlpool Calypso GVW9959K Top Load Washer - Page 2 Questions & Answers
Is the schematic for 8520870 control board available
there would be a wire diagram , which should include a schematic of the board and check points either within the console, or i believe on this unit its located in a clear plastice bag glued to the inside of the front panel, tip the machine back you sould be able to reach up and remove it that way
7/29/2014 4:36:37 PM •
Whirlpool...
•
144 views • 0 helpful votes
Control board
Call the manufacturer or get a multimeter to check things manually
7/29/2014 4:48:32 PM •
Whirlpool...
•
58 views • 0 helpful votes
Washer wiring diagram
It will be some where, try google, try espares.co.uk they are good for things like that, use them a lot.
7/29/2014 4:34:03 PM •
Whirlpool...
•
53 views • 0 helpful votes
What is era Code CI on a Calypso washer
A CI is an to high amp draw on the motor. In my experience it could mean your motor is bad, or motor control board is at issue. The only way to really check is to have an amp meter to see if the motor is drawing to many amps.
285917 MOTOR ABOUT $250
8571359 CONTROL BOARD ABOUT $200.
The biggest issue, is you may also have a transmission locking up, basket drive issues, bearing issues, etc causing the motor to pull the high amps.
5/29/2014 7:28:34 PM •
Whirlpool...
•
108 views • 0 helpful votes
Cabrio washer error code OL after about 10 mins.
The ol error can be caused by many problems, first let's address the over filling of the water, there is a plastic tube that runs from your control to the outer tub. This tube provides the pressure to the sensor in the control board to control the water level in the tub of the washer. If this line has a pin hole or is clogged, this could effect the water level. If your tube is ok then the control board is bad.
the ol error could be any of the following:
cloths under the tub,
bad bearings
basket hub
stater motor
rps sensor
control board I’m happy to assist further over the phone at
https://www.6ya.com/expert/donald_a8261495ff0777e2
3/27/2014 4:59:01 PM •
Whirlpool...
•
464 views • 0 helpful votes
Will not drain. need to know how to get to pump
Most pumps are in the bottom of the unit. Lift up and and support support on blocks. Look for round shaped device with tubing coming out. Normally, with slow or no drain it's clogged with lint. Clean out and reassemble and try a drain cycle.
1/5/2014 12:36:06 AM •
Whirlpool...
•
1,951 views • 9 helpful votes
What does F 02 code mean ?
Normally a simple fix: Tip the washer back at a 45 degree angle. On the bottom panel there are three or four screws, with the screws removed the panel will slide down and off. With the lower access panel now removed you will have access to the washers drain pump clean out. With the water already bailed from the washer you can twist the filter head counter-clockwise to remove. Twisting the filter head counter-clockwise will loosen filter so it can be pulled out. With the filter out clean and install it back into washer. Run a quick cycle to ensure the washer is back up and running and the F02 error has disappeared. If the error comes back, it may require you to clean the drain pump filter again.
5/4/2014 7:00:42 PM •
Whirlpool...
•
45 views • 0 helpful votes
Cement counterweight broken
difficult to do much there. you could try gluing something to the bowl, but it is very unlikely to hold for many cycles. you can buy new outer bowl / frames from the manufacturer.
11/19/2013 10:25:05 PM •
Whirlpool...
•
1,772 views • 1 helpful votes
Display will not clear. washer will not start
If you had to replace blown capacitors on the control board, whatever took them out most likely took out something else on the board at the same time. Causes are many...lightning strike, moisture, bugs etc. I would look carfully at the board with a magnifing glass...you might get lucky and find a short you can fix. If not, your probably going to have to invest in a new control board.
11/17/2013 1:27:43 PM •
Whirlpool...
•
77 views • 0 helpful votes
Not finding what you are looking for?