Motorola Mobility H550 - Bluetooth Headset - Black/Silver Wireless Headset - Answered Questions & Fixed issues

Hi,

follow the steps below:
• Setting the headset into pairing mode
1) Ensure the headset is fully charged
2) The headset must be switch off
3) Press and hold the on button for +- 8 seconds until the light flashes red-blue
4) The headset is now in pairing mode
• Searching for the headset on the phone
1) Go to “settings” or “connections”
2) Select Bluetooth, then options
3) Select Devices and click add
4) The phone should search for any available Bluetooth devices and display what was found
5) Select the Motorola device and click add
6) You will be required to enter in a pass code which is standard ‘0000’
7) If successful then the headset will start flashing BLUE every few seconds.
• The headset is now paired with the phone

Hope this helps
Season's Greetings from Fixya!

Chris (ziraffa)

Hi, In this HX550 Reset to factory default You will find the information you need to reset your device. Hope that helps. Regards, Maya Motorola Support

Did you mean an HX550? HX550 Pair connect with your phone . the H550 cannot be paired to more than one device. Mark Motorola Support

Long press the large multifunction button until the headset blinks and turns off. Mark Motorola Support

Contact Motorola Support: http:/www.motorola.com/support

Contact Motorola Support: http://www.motorola.com/support

In certain cases you are able to pop them open very carefully and replace the battery, all depends on what kind of battery it is. Most are now going to the small battery packs so if yours is new that is probably what it is and there isnt a way to replace.

You seem to have asked this question twice. Anyway, I'll post it again, just in case. As you have specified neither your headset nor your phone model, please, take a look at these general tips I posted a long time ago.Hope they might address your questions, somehow.Anyway, please, let me know if you need further informations. In this case, tell me your headset and phone models.Best regards,Carlos

Found this at another site. It worked for me. Good luck!!


Back to the phone, you want to hit "add new device". On certain models of phone you additionally have to select "search for devices". Your phone will recognize any headsets in pairing mode. When it is finished scanning, allow the phone to add your headset. It will ask you for the device pin code. This pin code will be 0000.

You could try the bluetooth generic passwords (0000 and 1234), these usually work with most devices.

Go to Settings, then Accessory settings, then audio device settings. Now change the input device by selecting it and change it to the motorola H550. Save these changes and It should work. Did for me at least. If you're still having issues or not seeing the option for your Bluetooth device, try going to manage Bluetooth Devices and see about registering it there.

You can download a manual HERE

If you are hearing the ringing in the ear piece, you are paired up. Try pressing the earpiece button, or you can just press answer on your phone.

Hi,you can follow the instruction to know how to connect blue tooth and the pin to use for pairing your phone .

How to Pair (Connect) a Bluetooth Headset to Your Phone

So you've heard of this new thing called "bluetooth..." But what is it? ...And what does it do for me? It's wireless technology that can link your phone to a headset, computer, another phone, or in extreme cases, your car and home.

We'll just start with the basics and connect a headset to the phone



Instructions



Things You'll Need:

* A Bluetooth cellular phone
* A Bluetooth Headset




Blue tooth can simply be called "a generic wireless technology that can connect your phone, computer, headset, PDA, laptop, and any other enabled device to each other."

In essences, it was designed to be a universal wireless connector between devices.

Ok... Here we go.
Make sure that both your phone and new headset are charged up.


Since every brand of headset is different, please refer to the instructions for "Pairing", but I will tell you how the most common headsets pair.

By the way, "Pairing" just means "connecting". If you find it more simple, you can substitute the word.

On most headsets, from the Headset being off, hold down the answer/end button down until the indicator light(s) glow a solid color (usually blue). This may take up to 10 seconds. They might flash first, then after a couple more seconds, go solid on.


On your handset, find the bluetooth menu.

On most phones, go to the settings menu, then to "connections" and then "Bluetooth". You are looking for a link to "Add a new device".

On Motorola phones, it is in the "Handsfree" link. Select [look for new device] select this option, and hit "OK".

Nokia Phones: look for "search for new audio enhancements". Hit OK.

On Samsung phones: **Bluetooth menu might be under "tools"** Look for "Add new device". Hit OK.


The phone will search for a couple seconds. If your headset is in paring mode, it will show up on the phone either with the name of device or something like this [unknown headset] or [b2.c3.f4.56.a1] (called a MAC address).

Either way, select it, and hit OK.


The phone will now ask you for a "Pin" or "Passcode", which is a 4 digit number. Headsets will ALWAYS have 0000 (four zeros) as a pin or passcode. I have never encountered a headset with a different number as a passcode. I have been in wireless for 10 years, and still have not found a headset that has any different numbers.

Enter these four zeros and select "OK"


The headset and phone will connect to each other. The phone will display a message that will be something to the effect of:
"Connected to headset".

At this point, the phone MAY ask if you want to use the headset. This means all audio from phone calls would be routed to the headset rather than in to the phone's speaker or earpiece. Select yes, or ok.


Your headset is now set up for you to talk on like a REALLY important CIA agent or something of the like...

Keep in mind that when a call comes in, the phone will still ring like normal.

You can answer the call by either:

1. Pulling the phone out of your pocket and hitting the answer button.
2. Touching the answer/end button on your headset without reaching for you phone.

The range of your headset is up to 30 feet, in a direct line of sight.

If you go into another room, your range may be decreased.

If you do happen to go out of range, the call will be transferred back to the phone, and as soon as you are in range again, touch the answer button on the headset to let the phone know you're back in range. It will re-transfer the call back to the headset.


If you turn off the phone, or headset, you can repair them again simply by going to the bluetooth menu and selecting the headset again from the list. It will reconnect without a pass code and you are up and running again.

*** Please note that you do not have to hold down the answer/end button on the headset until it goes a solid on again.

Tips & Warnings

If you have difficulty, please feel free to contact me and I'll help you get things sorted out.

Thanks for using fxya...

on the left and right side of the headset there are volume buttons.

Most Bluetooth headsets use 0000 (4 zeros) as the passkey when paring the device to the cellular unit.

try 0000

The passkey is 0000

You can get the manual on the link below.

http://static.compusa.com/pdf/Motorola-H550-Manual.pdf

Good Luck

Simply type 0000 in the space provided for the passkey.

Passkey = 0000

turn on the headset and then press all the volume buttons and the send button together until the light turns steady nlue and then search it with your phone.