20 Most Recent
Whirlpool RBS245PDS Electric Single Oven - Page 4 Questions & Answers
I get an F1 code when I bake and then it beeps and
F1 usually means that that the control board has failed. In rare cased depending on your model, the keypad can also cause an F1. If you disconnect the keypad from the control board and the F1 still comes on, it is definitely the control board. These can be refurbished at fixyourboard.com.
10/27/2009 6:52:34 AM •
Whirlpool...
•
Answered
on Oct 27, 2009
Control panel says e1 f1
Anything with 'F1' for Whirpool or GE means the control module has failed. We repair these frequently at fixyourboard.com. Do a google search and you can see you options.
10/26/2009 2:21:42 AM •
Whirlpool...
•
Answered
on Oct 26, 2009
My Whirlpoolis showing F-1 Error of the LCD
F1 code on your oven means "Electronic control malfunction". Clean contacts and reconnect all wires on the control board. If it does not help - replace oven control board. You'll also need to program the oven cavity size in the new control board. Model number is incomplete, so can't tell the part number, can be either 8301919 or 8301345
10/13/2009 11:57:08 PM •
Whirlpool...
•
Answered
on Oct 13, 2009
I have a four wire cable for electrical oven in
On 4 wires one is Ground, one is common, The other 2 are line voltage 110-130 VAC. Ground and Common serve the same purpose. Change the cable with the plug to match the outlet in the home ( get the cable off your old stove). Be sure the plug is out of the outlet. Hook up as in old stove.
If you do not feel confident get an electrician so you do not get hurt on burn down you home.
9/19/2009 12:41:01 PM •
Whirlpool...
•
Answered
on Sep 19, 2009
Dual wall ovens shut off
Would need the codes to be sure,but sounds like the control is out the part will run you around $200.00 And don't wait till two weeks before Thanksgiving cause you won't find one till after New Years by then.lol Hope this helped you ou.t
9/2/2009 12:09:30 AM •
Whirlpool...
•
Answered
on Sep 02, 2009
Whirlpool 27" wall oven. no heat after self clean
Self cleaning features are not recommended by most appliance technicians. The ovens are not constructed satisfactorily to expel the 1000 degree heat, Therefore the thermal fuses blow as well as other parts failures.
Remove the oven. Remove the rear panel. Replace the thermal fuse in the back of the oven. Use Easy Off next time.
5/12/2009 9:43:48 PM •
Whirlpool...
•
Answered
on May 12, 2009
Burners & clock are working, but oven, brioler & self-cleaner won't. Error F-0, EO
Brandyz
Most likely the problem with your range is the spark module. It is located in the control panel on the right hand side. You can access it by removing the back panel held with four screws from the back. Remember to unplug the range first. The name plate with the model number and the serial number is on the frame behind the storage drawer. You can buy the spark module here: http://click.linksynergy.com/fs-bin/click?id=SrmyP8LkIos&offerid=92089.545301030&type=10&subid=
It comes with installation instructions.
Gendos...post back
4/15/2009 6:32:19 PM •
Whirlpool...
•
Answered
on Apr 15, 2009
Door wont shut and the light stays on
Since this is a new install, check around the perimeter of the oven door and see if it is closing all the way flat against the surface. The hinge could have partially popped out and needs to be reset. Can you tell if the oven door is popped out at the top portion of the oven door or the lower portion of the door?
Waiting to hear from you,
Eric Campion
3/15/2009 7:55:06 PM •
Whirlpool...
•
Answered
on Mar 15, 2009
No power in heating elements
Check from your receptacle to the plug to the back of the oven. Then the wires that attach to the elements. Sounds like this is your problem. If this is not it, then you may have a bad board.
2/5/2009 3:11:50 PM •
Whirlpool...
•
Answered
on Feb 05, 2009
Not finding what you are looking for?