Whirlpool RBD305PDS Electric Double Oven - Answered Questions & Fixed issues
Upper oven bake coil stays on.
Stove will not turn offCHECK
Temperature Control Thermostat
If the oven won't turn off the oven thermostat is often the cause of the problem. The electrical contacts inside the oven thermostat can weld themselves together and then the oven won't turn off. If this happens, turn off power to the entire appliance at the household circuit breaker or fuse. The oven thermostat usually cannot be tested and must be replaced if defective.
Oven Control Board
The oven control board has a set of relays that turn on and off power to the bake and broil circuits according to the customer settings and sensor input. If the oven won't turn off it could be that one of the relays on the oven control board is shorted closed, providing voltage to the heating circuit. It can be dangerous if the oven won't turn off. Don't leave the oven unattended without turning off power to the oven.
Relay board:
Some ovens are equipped with a relay board. This circuit board has several relays which control the switching of electrical current to the oven heat source. If the oven won't turn off it may be that one or more of the relays on the relay board have failed. If this happens replace the relay board. The relays on the board are not sold separately.ALSO CHECK THE BAKE AND BROIL ELEMENT.
: I offer free advice bcuz God is so good!
3/20/2020 8:36:29 PM •
Whirlpool...
•
Answered
on Mar 20, 2020
•
156 views
CAN NOT CONTROL BOTTOM OVEN
I assume yiu had the electronic oven control repaired. Sometimes the touch pad also goes bad. I have had to replace them at the same time. If the oven indicator lights showing the oven being on shows up on the display it could be that the thermal fuse behind the oven has gone out. this in in the common line and will shut down both ovens at the same time but you will get the control panel to respond to the touch pad.
11/28/2013 3:28:52 AM •
Whirlpool...
•
Answered
on Nov 28, 2013
•
154 views
Whirlpool Double oven control panel
A lot of people seem to have ran into this problem. I had no luck finding a solution to this problem anywhere on the internet. I finally fixed this problem by replacing the control board. Wanted to put this info out here for others. The part swaps out fairly easy for all of you considering the fix yourself. Sears direct had the cheapest price.
12/24/2012 3:34:39 PM •
Whirlpool...
•
Answered
on Dec 24, 2012
•
1,257 views
I want to replace the
You need to remove oven top cover--6 screws. You may need to bend 2 flaps out of the way next to power conduit.
1/27/2011 9:13:42 PM •
Whirlpool...
•
Answered
on Jan 27, 2011
•
871 views
After self cleaning the display is blank and door is locked
Which thermal fuse did you replace?
There are 3.
This manual will help you diagnose the oven.
Thermal fuses are explained on page 3-2.
https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/7d69e72584ddde3385256a7e00524e76/$FILE/8178007.pdf
7/11/2010 7:50:59 PM •
Whirlpool...
•
Answered
on Jul 11, 2010
•
647 views
How to remove the control panel on Whirlpool double oven Model RBD305PDS14
Remove the doors by turning toward you a little toggle apparatus located on each hinge. Locate a small screw on the lower inside edge of the left and right hand trim and then slide off the trim. Remove the lower trim then raise the upper trip and put the left end of the panel inside the top opening. This allows you access to the control panel. Test both the keypad part #8300440 and the control panel part #830219 to see which one needs to be replaced. Order the replacement part, plug it in, reverse the precess above and it should work like new..
11/9/2013 6:32:50 PM •
Whirlpool...
•
Answered
on Nov 09, 2013
•
7,248 views
Whirlpool YWFE710H0BS0 oven no longer heats up.
Check the elements for continuity with a multimeter. Sometimes the connectors draw too much current and can burn out as well. Both are easy tests. A runaway temperature can make elements fail because there is no thermostatic control, they just glow bright yellow..
8/26/2023 10:38:37 AM •
Whirlpool Ovens
•
Answered
on Aug 26, 2023
•
56 views
What does E1 F2 code means?
Greetings,
This might indicate a bad keypad or that the cable connecting the keypad to the chip board within your whirlpool has come loose. You might need to work with whirlpool to see if they keypad needs replacing or if the internal chip board itself is faulty.
Thank you.
4/24/2023 6:16:24 PM •
Whirlpool Ovens
•
Answered
on Apr 24, 2023
•
83 views
Not finding what you are looking for?