Top 20 Whirlpool RBD305PDS Electric Double Oven Questions & Answers

Stove will not turn offCHECK

Temperature Control Thermostat

If the oven won't turn off the oven thermostat is often the cause of the problem. The electrical contacts inside the oven thermostat can weld themselves together and then the oven won't turn off. If this happens, turn off power to the entire appliance at the household circuit breaker or fuse. The oven thermostat usually cannot be tested and must be replaced if defective.

Oven Control Board

The oven control board has a set of relays that turn on and off power to the bake and broil circuits according to the customer settings and sensor input. If the oven won't turn off it could be that one of the relays on the oven control board is shorted closed, providing voltage to the heating circuit. It can be dangerous if the oven won't turn off. Don't leave the oven unattended without turning off power to the oven. Relay board: Some ovens are equipped with a relay board. This circuit board has several relays which control the switching of electrical current to the oven heat source. If the oven won't turn off it may be that one or more of the relays on the relay board have failed. If this happens replace the relay board. The relays on the board are not sold separately.ALSO CHECK THE BAKE AND BROIL ELEMENT. : I offer free advice bcuz God is so good!

I assume yiu had the electronic oven control repaired. Sometimes the touch pad also goes bad. I have had to replace them at the same time. If the oven indicator lights showing the oven being on shows up on the display it could be that the thermal fuse behind the oven has gone out. this in in the common line and will shut down both ovens at the same time but you will get the control panel to respond to the touch pad.

Here is the basic removal process:http://blog.applianceboards.com/installs/how-to-remove-an-oven-control-board/

You need to remove oven top cover--6 screws. You may need to bend 2 flaps out of the way next to power conduit.

Which thermal fuse did you replace?
There are 3.
This manual will help you diagnose the oven.
Thermal fuses are explained on page 3-2.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/7d69e72584ddde3385256a7e00524e76/$FILE/8178007.pdf

Hi,
If your electric oven is not heating then you probably have a bad heating element in your oven. This is not that hard to fix yourself...
Check out this tip that I wrote about the Oven not heating problem..

Oven Problems Electric Oven is Heating Slowly or Poorly
http://www.fixya.com/support/r4511800-oven_problems_electric_oven_heating

heatman101

This indicates an oven temperature sensor problem. Here is a link that should help http://appliancehelponline.com/oventempprobe.html

Hi,
Seems like you found out the hard way what I wrote about in this tip...
Check it out it also contains some thing to try on how to unlock that oven..

Self Cleaning Oven Problem
http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101
Asker's Testimonial " Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!! " - amymrocks

Hi,

This error refer to bad touch pad / console. Once replaced it would resolve the problem.

In the mean while, you could Disconnect the power supply for few minutes and then turning it on. Sometimes, this might work as it would reset the oven.

Let me know,if needed further assistance,

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

HI. This code alert is a strong indication of door switch mechanism failure. The device is not responding to the lock/unlock command. Check to see if the door switch is completely closed. Check latch, solenoid, and actuation switch for electrical or mechanical malfunction.

You will need to obtain a ohm meter for this test. Follow the procedure below to assist with the testing phase. replace the door switch if it fails the electrical test.

Before repairs or further testing can begin you must disconnect the electricity at the fuse panel, at the circuit breaker panel, or by pulling the plug. Make sure the power is off before proceeding.After gaining access to the door latch switch, Set the latch to the "clean" position and test for circuit continuity at the terminals of the switch with your VOM's ohmmeter function. If there is no continuity, the switch is faulty. Use caution when testing.

• Additionally, check the wires for a tight fit at the door switch, and to the control board. In some cases, the code will appear if the wires have become separated, or slightly worn.

E1-F5 - Failed door switch mechanism.

First of all try the reset method. hold cancel/off for more then 5 seconds and check out does the error gets reset.if not then turn the unit off then on it again and try the same reset procedure again. but if still the same exact error problem then its the confirm problem of oven door latch assembly mechanism. hear is the part which you need to replace.click on the link directly http://www.repairclinic.com/SSPartDetail.aspx?PartID=589939&PPStack=1 This is the complete lock/latch assembly for your model, which includes the micro switch and solenoid: ------ to do this replacement/repairing your self you will require a service manual. to get the service manual please click on the link directly http://adcxns1.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/ca8e028c60d9804f85256a8c00621f04/$FILE/4322089.pdf in the service manual.check on page number 12,16 and 22.for door and door lock assembly.
You can get required parts from www.repairclinic.com
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

good day,
hope this link below will solve your problem.

ovens

Ok, this is defiantly control failure and i will post a link to a repair site that is bookmarked on the board that you will need to order.

CLICK HERE TO PURCHASE A REPLACEMENT CONTROL BOARD(ECU,EOC)

Please rate and god bless:)

Remove the power from the oven. Open the control panel and unplug the keypad ribbon from the control board. Assemble the control panel back and turn the power on. Wait a few hours.
If the error code came back on, replace the control board.
If the error code did not show up, replace the User interface (the key pad comes as a control panel assembly).
Here are the user interfaces available for this model please choose the right color
WHITE>
http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=831537&PPStack=1
BISCUIT>
http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=905740&PPStack=1
BLACK>
http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=904495&PPStack=1
CONTROL BOARD>
http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=1027942&PPStack=1

Thank You

Bad switch!

Remove the doors by turning toward you a little toggle apparatus located on each hinge. Locate a small screw on the lower inside edge of the left and right hand trim and then slide off the trim. Remove the lower trim then raise the upper trip and put the left end of the panel inside the top opening. This allows you access to the control panel. Test both the keypad part #8300440 and the control panel part #830219 to see which one needs to be replaced. Order the replacement part, plug it in, reverse the precess above and it should work like new..

A lot of people seem to have ran into this problem. I had no luck finding a solution to this problem anywhere on the internet. I finally fixed this problem by replacing the control board. Wanted to put this info out here for others. The part swaps out fairly easy for all of you considering the fix yourself. Sears direct had the cheapest price.

Never ever use the Self Cleaning Feature. Its main function of to break things like elements, door looks and frazzle control boards. That keeps the maker is steady sales of spares. My old Ge Stove is from the mid 1970s. Of course they don't make them like that any more. They are non-electronic, so only elements can fail. You can check elements for continuity with a multimeter and replace them. If you fancy a new one, get one but never use the self cleaning feature and it will indeed last you 30 years. Bake elements https://www.google.com/search?q=Whirlpool+stove+bake+element ..

Never ever use the features of a Self Cleaning Oven. We see the damage they do here on Fixya, and the worst is the door not unlocking, and the most expensive is when they fry the mainboard. They all have a door interlock. If you were to open it when it was running, it would frizz your eyebrows!

Why You should Never Run A Self Clean Oven Cycle & ...

General Appliance Service https://www.generalappliancesvc.com > why-you-shou... Jan 29, 2020 - A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters with an extremely high temperature (932 F° or ...

Self-cleaning oven

Wikipedia https://en.wikipedia.org > wiki > Self-cleaning_oven A self-cleaning or pyrolytic oven is an oven which uses high temperature (approximately 932 °F (500 °C)) to burn off leftovers from baking, without the use ... ‎Pyrolytic process · ‎Alternative technologies · ‎Catalytic cleaning

Self-Cleaning Oven: 6 Reasons to Stop Using Feature ...

FIX Appliances CA https://fixappliances.ca > 4-reasons-stop-using-self-cle... A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters at an extremely high temperature (932 F° or 500 C°) to aid in ... ‎How Self-Cleaning Ovens Work · ‎Major Parts Damage ..

if wiring ok possible weak ignitor