Amana GMH950453BX Gas Furnace - Answered Questions & Fixed issues


Either you have a safety switch tripped or a faulty circuit board. Test all of the limit and roll-out switches, they should all read closed with an ohm meter.

Amana... | Answered on Dec 09, 2014 | 218 views


Control fuses only blow with a 24 volt problem. Make sure that you replace it with a fuse NO LARGER than 5 amps.You could have a thermostat wire pinched or some wire touching the cabinet inside the unit, but it is a 24 volt problem.

Amana... | Answered on Dec 09, 2014 | 364 views


google online an print

Amana... | Answered on Nov 26, 2014 | 255 views


make sure thermostat is calling for heat if so check safety circuit starting with the fuseable link if ok check to see if gas valve has voltage if so bad valve if not keep checking the safety circuit

Amana... | Answered on Oct 15, 2014 | 70 views


Sounds like you may have a dirty flame sensor. Try cleaning it with steel wool or Emory cloth.

Amana... | Answered on Jul 30, 2014 | 88 views


Believe that is hot surface ignition...so it should relight itself. turn the power off & back on, the power outage could have messed with the circuit board

Amana... | Answered on Dec 06, 2013 | 85 views


Hi Brandon , seems like you have a dirty flame sensor . Clean the sensor if that doesn't work check for continuity in the high limit fuse .

GOOD LUCK
APPLIANCES R'EN

Amana... | Answered on Dec 06, 2013 | 282 views


Just a guess unless you read from a paper on the inside what 4 flashes mean but usually it's the igniter

Amana... | Answered on Nov 24, 2013 | 266 views


This is a small furnace is your home about 1,000 sf? If your home is a 2000 sf home it may be too small and therefore low air flow. Otherwise you can try putting high speed black wire to heat on the circuit board. Or you have a main duct down somewhere.

Amana... | Answered on Nov 10, 2013 | 79 views


do a search for the mfg and see if you can download a manual
or put the name and the model number in a search engine along with words user manual and see if you can find one

Amana... | Answered on Oct 20, 2013 | 251 views


What is -the outside?
Heat pump, gas, electric heat combination?
You may need to back track, double check the Honeywell configuration jumper or software settings for your type of heating used.

Amana Heating &... | Answered on Nov 09, 2019 | 18 views


check for flame below flame sensor possible blockage of tube

Amana Heating &... | Answered on Oct 19, 2019 | 31 views


There should be a fan symbol on your remote control. In the "mode" control, there should be the following options.. Heat, cool, Auto and fan. If you select fan, only the fan will run. No heating or cooling.

Amana Heating &... | Answered on Jun 10, 2019 | 27 views


Check voltage in , there could be one side of breaker burned causing only one side to come through. This happens on older main breakers frequently which messes up whole house.

Amana Heating &... | Answered on Jun 10, 2019 | 61 views


How are you determining that one section.is cold and one warm? If this is in fact the case you have a blockage in the coil or a compressor that is down provided this is a multi compressor unit.

Amana Heating &... | Answered on Feb 06, 2019 | 73 views


I'm leaning 2 directions, one is that your tstat is sensing your heatpump can not keep up with the load. Therefore bringing on heat strips or two, you have a cycles per hour limit set for compressor heating and your machine is cycling too often.

Amana Heating &... | Answered on Jan 27, 2019 | 36 views

Not finding what you are looking for?
Amana GMH950453BX Gas Furnace Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Amana Heating & Cooling Experts

Donni Steen

Level 3 Expert

687 Answers

Bill Long

Level 3 Expert

606 Answers

WatsHVAC

Level 1 Expert

35 Answers

Are you an Amana Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...